[H.W₁]: Designop-Amp circuit that produceoutput given by V₂ = -(4V₁ + V₂ +0:11₂)if v₁ = 2 sin wt ; V₂ = 5V, and V₂ = -100vSketch the output voltage waveform?Aris:13V5Van→→tمطلوبتسليمةan

Answered: Image /qna-images/answer/dbc4ba16-fc64-4bde-9178-8a50afbfa51e.jpg

[H. W₁]: Design an op-Amp circuit that produce output given by Vo= -(4V₁ + V₂ +0:1√₂) if y₁ = 2 sin wt ; V₂ = 5V, and V₂ = -loov Sketch the output voltage waveform? Aris: 13V 5v A₂ V مطلوب تسلية an

[H. W₁]: Design an op-Amp circuit that produce output given by Vo= -(4V₁ + V₂ +0:1√₂) if y₁ = 2 sin wt ; V₂ = 5V, and V₂ = -loov Sketch the output voltage waveform? Aris: 13V 5v A₂ V مطلوب تسلية an

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A boost converter is required to have an output voltage of 8 V andsupply a load current of 1 A. The input voltage varies from 2.7 to4.2 V. A control circuit adjusts the duty cycle to keep the outputvoltage constant. If the switching frequency is 200 kHz, determine:i. a value for the inductor such that the variation in inductorcurrent is no more than 40% of the average inductor current forall operating conditions.ii. a value for the capacitor such that the output voltage ripple isno more than 2%.iii. in case the OFF period is reduced by 30% for constantfrequency operation, find the new output voltage
A step down converter has a load resistance R-0.50hms. an input voltage Vs-200V and a battery voltage E-20V. The average load current la=250A and the converter frequency is 400 Hz. The value of the inductance L that would limit the maximum load ripple current to 5% of la, would be equal to: Select one: O a. 9 mH O b. None of these O c. 26 mH O d. 15 mH
Consider a step up converter with a resistive load of value R-5 Ohms. It is supplied by a DC power source of magnitude Vs=200 V. The switching frequency is 5 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L-10 mH. The switch is supposed to be ideal. The peak input current 12 = 81A. RMS load current 10 is equal to: Select one: a. 39.15A Ob. None of these c. 74.36A O d. 55.16A 4
A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/3. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state : V. Find the peak and mean of the switch current.
Design a buck-boost converter to supply a load of 75 W at 50 V from a 40-V source. The output ripple must be no more than 1 percent. Specify the duty ratio, switching frequency, inductor size, and capacitor size.
H: Design OP-Amp eircwt that Poduce an out Put an given by Uo = - ( 4 V,t Uz to.l U3) If u, = 2 sinwt = 5 V and U3 = - 100V sketch the ont Put vo ltage waveform ?
Home Work: 1- Design a clipper circuit that can pass only the positive values (V22V) of a sinusoidal input voltage of 1KHZ and peak voltage of 4V. Use silicon diode. 2- Suppose you have an input sinusoidal voltage of f=1 KHz, Vpeak-4V. Design a clamping circuit that can positively clamped the input signal at -2V. Use a silicon diode of forward and reverse resistances of (r-62) and (r-9MS2) respectively.
c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/2. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state: i. Draw the converter circuit. ii. Determine the inductor's turn ratio. iii. Determine the primary inductance. Sketch the diode current and switch current. iv V. Find the peak and mean of the switch current.
r:09 A moodle1.du.edu.om An application demands that sinusoidal pressure variation of 250 Hz be measured with no more than 2% dynamic error. In selecting a suitable pressure transducer from vendor catalog, you note that a desirable line of transducer has a fixed natural frequency of 500 Hz but that you have a choice of transducer damping ratio of between 0.5 and 1.5 in increments of 0.05. select a suitable transducer. The value of damping ratio is between the following values Select one: O a. 0.707 and 0.807 O b. 0.631 and 0.692 O c. 0.2356 and 0.5625 O d. 0.5215 and 0.5625 Previous page Next page 1 Aşsignmen
The buck converter with resistive load has the input voltage of 30[V], the output voltage of 10 (V] (constant), and the switching frequency of 30 [kHz]. If the output average power is 20[W], then determine the size of the inductor such that the minimum inductor current is 25 % of the average inductor current.
A three-phase full-wave half-controlled converter supplies a highly inductive load with R = 10 the supply is a three- phase star connected with 400 V RMS. The value of firing angle in degrees, to obtain the dc output current as 15 A is