H.W: If you were an engineer in a company that has aproblem reading the gauge pressure precisely by amanometer in the following Figure. How would you help Fluidto solve this issue? If you know that the pressuredifference is really low. Analyze the problemmathematically and try to repair it in the simplest, andeasiest, way. Provide some suggestions and solve themmathematically to improve your point of view.Given:The fluid flow in the channel is Air.The working fluid of the manometer is Mercury.The Pressure difference between points 1 and 2 is 130 pa.A flow sectionor flow deviceB

Here's a step-by-step detailed approach to improve the readability of low gauge pressure differences…

Answered: H.W: If you were an engineer in a…

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 22P

See similar textbooks

Similar questions

Fluid mechanics, I need solutions in 15 minutes please. MCQ/A block of steel (s.g. = 7.85) will "float" at a mercury - water interface as shown in the figure. What is the height that submerged in the mercury (b)? Assume that the dimensions of the base of the block are X and L. A-269.247 mm B-139.251 mm C-237.008 mm D-297.826 mm E-208.140 mm F-164.025 mm G- 114.018 mm H-192.048 mm I-251.178 mm J- 324.085 mm
Moment of Inertia about the centroid. Please show your solution on a paper with complete details and equation and FBD
Kindly show the COMPLETE STEP-BY-STEP SOLUTION, DON’T DO SHORTCUTS OF SOLUTION, so I can understand the process. I will rate you with “LIKE/UPVOTE," if it is COMPLETE STEP-BY-STEP SOLUTION. If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with “DISLIKE/DOWNVOTE.” Topics related to the question: Statics of Rigid Bodies, Force System of a Force, Moment of a Force, Moment of a Force-Scalar Formulation, Moment of a Force-Vector Formulation, and Principle of Moment, Simplification of a Force System and Couple System, Reduction of Simple Distributed Load Thank you for your help.
Please solve step by step and give an explanation. thank you i am confused, because previous answers were usually -1 kpa but shouldn't the pressure be positive because the fluid on the right part is much higher(meaning that the pressure at b is greater than the other side
Hello expert! Please show complete step-by-step solution; because I want to understand the process, then I will rate you with upvote/like. If it's incomplete solution, I'll rate you with downvote/dislike. Include the reaction of forces in the free body diagram. Kindly make sure that your solution is readable and clear please. Thank you so much for your help, Expert!
Please solve and give an explanation. thank you i am confused, shouldn't the pressure be negative because the fluid on the right part is much higher(meaning that the pressure at b is greater than the other side?
CIVIL ENGINEERING FDRAULICS dynes A capillary tube of a uniform bore is dipped vertically in water which rises by 7 cm in the tube. Find the radius of the capillary if the surface tension is 70- Cm A liquid rises to a height of 9 cm in a glass capillary of radius 0.02 cm. What will be the height of the liquid column in a similar glass capillary of radius 0.03 cm?
The U-tube manometer in Figure 1 is open to the atmosphere. It is connected to a tank. There are 4 fluids inside the tank and manometer. Derive a formula to get the gage pressure in A. Draw your diagram with labels. Assume different specific gravities for the fluids and different heights of the fluid column. All interfaces are not of the same height or level. FLUID 2 FLUID 2 FLUID 4 A) FLUID 3 FLUID 1 Figure 1 Set A. Illustration for Problem 3. All fluids are of different specific gravities.
1 Proof that a solid aluminum block of 4 mm x 3 mm x 3 mm, such as shown in FigureQ1 (a), can float on water at 20 °C due to the effect of surface tension. The density ofthe aluminum block is 2700 kg/m3. Determine the contact angle. 2. A solid alloy cylinder having a diameter of 6.48 cm slides downward at a terminalvelocity of V through a vertical pipe. The downward motion is resisted by an oil filmbetween the piston and the pipe wall. Determine the oil viscosity when the velocityV is 5 m/s. The inner diameter of the vertical pipe is 6.5 cm, and the alloy density is3500 kg/m3.
b) The U-tube manometer can be used to determine pressure difference between two systems.This type of manometer is called a differential U-tube manometer. Consider the differentialmanometer connected to a pipe, as shown in Figure 1. Explain step by step on how you cancalculate the pressure difference between point A and B.
I was wondering in the hydrodynamics how i can determine Cp in the pressure ressistance (coefficient pressure). so the total ressistance will be Rt= Rf+Rp. Given in Coefficients it will be: Ct=Cf+Cp now they say Cp in % of the friction coefficient (Cf). Ct=(1+k)*Cf with 1+k the formfactor. so the total ressistance will be Ct=Cd*1/2*ρ *v^2*S (wetted area m^2, v= velocity in m/s and ρ= 1025 kg/m3 for salt water) kan you explain me how to calculate the Cd in the total resisstance?
Explain The major component of Menard’s prototype pressuremeter apparatus.

SEE MORE QUESTIONS

Recommended textbooks for you

Engineering Fundamentals: An Introduction to Engi…

Civil Engineering

ISBN:

9781305084766

Author:

Saeed Moaveni

Publisher:

Cengage Learning