H.W1 A belt drive system shown, is used as a speed reducer. The input shaft rotates at 2000 rpm and has a 144-tooth sprocket with a pitch diameter of 360 mm. The output shaft has a 72-tooth sprocket with a pitch diameter of 90 mm. The center distance between the two shafts is 750 mm. Determine the following for the belt drive: a. The velocity ratio b. The angular velocity of the output shaft c. The linear belt speed

H.W1 A belt drive system shown, is used as a speed reducer. The input shaft rotates at 2000 rpm and has a 144-tooth sprocket with a pitch diameter of 360 mm. The output shaft has a 72-tooth sprocket with a pitch diameter of 90 mm. The center distance between the two shafts is 750 mm. Determine the following for the belt drive: a. The velocity ratio b. The angular velocity of the output shaft c. The linear belt speed

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A synchronous belt drive system is used as a speed reducer. The input shaft rotates at 1000 rpm and has a 36-tooth sprocket with a pitch diameter of 3.609 in. The output shaft has a 72-tooth sprocket with a pitch diameter of 7.218 in. the center distance between the two shafts is 15.01 in. Determine the following for the belt drive: a. The velocity ratiob. The angular velocity of the output shaftc. The linear belt speedd. The belt wrap on the input and output sprocketse. The belt perimeter lengthf. Draw the schematic of the belt drive system
A synchronous belt drive system is used as a speed reducer. The input shaft rotates at 1000 rpm and has a 36-tooth sprocket with a pitch diameter of 3.609 in. The output shaft has a 72- tooth sprocket with a pitch diameter of 7.218 in. the center distance between the two shafts is 15.01 in. Determine the following for the belt drive: a. The belt wrap on the input and output sprocketsb. The belt perimeter lengthc. Draw the schematic of the belt drive system
Two mating involute spur gear of 20° pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of the teeth is 12 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length, find : a. The addendum for pinion and gear wheel; b. The length of the arc of contact; c. The maximum velocity of sliding during approach and recess. Assume pinion to be the driver.
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 ifits gearbox 5th gear is selected. The gear’s teeth are of involute form with amodule of 8 mm, an addendum is double the module, and the pressure angle isequal to 20° .1.1. If the driving shaft of the front wheels of the truck is connected to the output shaftof the gearbox, determine the number of teeth on the pinion to avoid interferenceand the corresponding number of teeth on the gear wheel.
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 if its gearbox 5th gear is selected. The gear's teeth are of involute form with a module of 8 mm, an addendum is double the module, and the pressure angle is equal to 20°. 1.1. If the driving shaft of the front wheels of the truck is connected to the output shaft of the gearbox, determine the number of teeth on the pinion to avoid interference and the corresponding number of teeth on the gear wheel. 1.2. Calculate the gear maximum velocity of sliding.
A gear set consists of a pinion and a wheel with pitch circle diameters of 90 mm and 260 mm respectively and a module of 4 mm. The pinion has 16 teeth. The pressure angle is 20° and the addendum is 1 module. Calculate: 2.1. The length of the arc of contact if the pinion is a driver. 2.2. The maximum velocity of sliding between the teeth when the pinion rotates at 90 rev/min.
A synchronous belt drive system is used as a speed reducer. The input shaft rotates at 1000 rpm and has a 36-tooth sprocket with a pitch diameter of 3.609 in. The output shaft has a 72-tooth sprocket with a pitch diameter of 7.218 in. the center distance between the two shafts is 15.01 in. Determine the following for the belt drive: d. The belt wrap on the input and output sprocketse. The belt perimeter lengthf. Draw the schematic of the belt drive system
The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating at a speed of 1200 revolutions per minute. It must increase the torque received at its input shaft 16 times. Spur gears with 20° pressure angle should be used. Input and output shafts should be aligned. The transmission should take up as little space as possible. The distance between the centers of the input shaft and the intermediate shaft (the one that loads gears 3 and 4) should be 10 inches. Determine the magnitude of the radial load that gear 4 exerts on gear 4. Write your answer in pounds.
3.Two gears of module 4mm have 24 and 33 teeth.The pressure angle is 20° and each gear has a standard addendum of one module.Find the length of arc of contact and the maximum velocity of sliding if the pinion rotates at 120r.p.m
The maximum sliding velocity of the teeth of two gear wheels in mesh is 0.32 m/s. The wheels are of module 5 mm and have 32 and 44 teeth respectively. The addendum for each wheel is 1.2 times the module and the pressure angle is 20°. Calculate: 2.1. The number of teeth in contact. 2.2. The angular speed of each wheel.
Question 1 A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 if its gearbox 5th gear is selected. The gear’s teeth are of involute form with a module of 8 mm, an addendum is double the module, and the pressure angle is equal to 20°. 1(a). If the driving shaft of the front wheels of the truck is connected to the output shaft of the gearbox, determine the number of teeth on the pinion to avoid interference and the corresponding number of teeth on the gear wheel. 1(b) Calculate the gear maximum velocity of sliding.
Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and transmits a torque of 20 N-m. The torque transmitted by the gear is