he axle of the freight train is subjected to loadings as shown below. The diameter of the axle is 137.5 mm. If it is supported by two journal bearings at C and D, determine the maximum bending Stress. Include a FBD, SFD and BMD using either the section or graphical method. Draw a cross-section of the shaft and indicate the points of maximum tension and compression.

Q: Fbd ,formula and calculation should be included. Please work it fast without wasting a time. 1)The…

A: According to the given data Segment  Diameter Length AB 20mm 1.5m BC 80mm 1.7m Modulus of…

Q: A plant G(s) has 4 simple poles: -20, -10, -5 and -1.1 and 2 simple zeros: 0 and 2.3. The asymptotes…

A: 4 simple poles: P=4 : -20, -10, -5, and -1.1 2 simple zeros: Z=2 : 0 and 2.3 To find: asymptotes of…

Q: I would like to know how to determine the maximum bending moment step by step

A: Here you want to know how to determine the maximum bending moment

Q: Calculate belt length in inches   Answers: A) 66.8 in. B) 59.98 in.  C) 45.06 in.  D) 62.75…

A: The length of the belt. Given: The diameter of the larger pulley is D=8.5 in. The diameter of the…

Q: True/False Statement: A cable is a load bearing component that can only support tensile forces. True…

A: Answer: False. usechatgpt init success

Q: a(m/s) 25- 18 -r(s) Part A A two-stage missile is fired vertically from rest with an acceleration as…

A:

Q: 8. As the linkage rotates, box A undergoes a) general plane motion c) linear translation b) pure…

A: In this four-bar mechanism, (s+l=p+q) has pair  of equal lengths, so this is a parallelogram…

Q: Consider the following system. Assume m = 1 kg, k = 7000 N/m and c = 70 N.s/m. The damping ratio of…

A: The damping ratio of the second mode. Given: The mass is m=1 kg. The spring constant is k=7000 N/m.…

Q: he rectangular plate shown below weight 100lb. and is held in position by a cable EF and hinges at A…

A: Given Weight = 100 lb To find Tension in cable Reaction at A and B

Q: A 60 kN -5 m 80 KN T -5 m- B 5 m 5 m EA constant

A: The reactions and all member forces. FBD: The free-body diagram is shown below.

Q: (a) Find the centroid(x,y) of the composite area shown below. (b) Determine the area moment of…

A: Given: Find: a) Centroid (x,y) of the composite area. b) The area moment of inertia (lx, and ly) of…

Q: Q2)A concentric spring consists of two helical compression springs having the same free length. The…

A:

Q: A certain two dimensional shape has the following integrals f dA = 4.5 in² fx dA fyd A S x² dA 13.5…

A:

Q: The drawing represents a planetary reduction gear used in aeronautics. Calculate the speed of the…

A: Speed of motor: N3=1200 rpm and considering N1=0 (is fixed) Number of teeth: Z1=50 teethZ2=18…

Q: In a container of diameter Φ (see image), a tube of diameter ε (much smaller than the diameter of…

A: Given data: Diameter of the container of = Φ  Diameter of the tube = ε (much smaller than the…

Q: Q6. A square bottom container with a side of 36" and a height of 240" contains SAE 30 oil and water…

A: Given data:- A square bottom container with a side = 36 in height =240 in contains SAE 30 oil and…

Q: A block of mass of 3kg is being pushed by of force F= 200N at an angle of 0 = 10° to the horizontal…

A:

Q: he force P = 150 N is applied to the 50-kg crate, which is stationary before the force is applied.…

A: The normal force (N) is the perpendicular force exerted by the surface on the crate, which…

Q: A dc transformer is supplied with electric power at 230 watts with an input voltage of 220 volts.…

A:

Q: Determine the forces in a. Support reaction at A b. Support reaction at B C. Member in BC d. Member…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: 4. Andrew, whose mass is 60 kg, spins a ball of mass 0,4 kg on a frictionless table top with a…

A: Given: Mass of Andrew = M = 60 kg Mass of ball = m = 0.4 kg Angular velocity = ω= 5 rad/s length of…

Q: Problem 23.2 For a piston cylinder system where the air inside the piston begins with a pressure of…

A:

Q: Low flow occurs in a pipe with Reynolds number equal to 1,450. Determine the friction factor for…

A:

Q: 2. Tid the percentage mercase in specu, in the Danis rise by 20 min. [Alls. 370] A Porter governor…

A: Ball 1 mass, m=3 kg Ball 2 mass, M=15 kg Arm length, BP=BD=200mm =0.2m Minimum radius of rotation,…

Q: 3. If we replace the distributed loading on the right by a single resultant force, how far from…

A: According to the given data A Beam with Uniform distributed load (Udl) and Uniform varying load…

Q: As shown in the Figure below, the speed of the transmission shaft is n=200 r/min, the input power of…

A: Speed of transmission shaft, n=200 rev/minInput power of A, PA=40 kWOutput powers,For B, PB=20 kWFor…

Q: Problem 1: A uniform beam of mass M = 100.0 kg and length L = 20.0 m has a load of m₁ = 3000 kg at…

A: According to the given data M=100kg Mg=100x9.81=981 N mL=3000kg mLg=3000x9.81=29430N T=12000N We…

Q: 1. Using the Taylor equation for tool wear and let: n = 0.3, calculate the percentage increase in…

A: The percentage increase in tool life.

Q: 6. In the figure shown below, a 3.5 g bullet is fired into a vertically balanced plate with a…

A:

Q: What are some steps that might be taken in the next 10 to 30 years to improve the sus- tainability…

A: Improving the sustainability of energy use is a complex, multifaceted problem that requires actions…

Q: Pin P is constrained to move along the curve defined by the lemniscate r= (k sin 20) ft. The angular…

A: r=ksin2θ ftθ=3t1.5 radk=9θ=60°=π3

Q: In a steam power plant 1.5 kg of water per second is supplied to the boiler. The enthalpy and…

A:

Q: the ground and free in the upper end. a) Calculate the compressive stress, then the minimum…

A: Given Data: H=3 mm=1000 kgFOS=3σut,c=241 MPaE=190 GPa   To Find: (a) The compressive stress. (b) The…

Q: What is the angle between [-112] and [210] direction vectors in the cubic system? O 121.04 O 100.51…

A: According to the given data Vector h k k 1 -1 1 2 2 2 1 0 We need to find Angle b/w them

Q: a closed system contained a copper block of density 9.96g/cm3 at 25 degrees celsius in reversible…

A:

Q: Please answer correctly. 2) Is it possible to reduce the volume of an ideal gas in a closed…

A:

Q: The following vibration system oscillates with a small angle. x = 0.6m, y = 1.8m, k = 18N/m. From…

A: Given Data: x=0.6 my=1.8 mk=18 N/m∆=0.2 mω=30 rad/sθ=2 radmA=10 kg   To Find: 1. The natural…

Q: Q2:A) What are the classifications of the NACA Aerofoil section? B) Select the appropriate NACA…

A: A) The NACA (National Advisory Committee for Aeronautics) Aerofoil section is a standardized system…

Q: Calculate the belt length in inches

A: According to the given data d1=8.5 in d2= 4.75 in Horizontal distance b/w centers of the pulley=19.5…

Q: Q1 Q2 "Alpha Symmetry depends on the angle through which a part must be rotated about an axis…

A: Question 1 False. Alpha symmetry refers to the rotational symmetry of a three-dimensional object,…

Q: 4₁ P Answer: 90° L2 Ľ. X For the beam shown, you are provided the values P = 590 N downwards, L1= 2…

A:

Q: The following lead screw and saddle arrangement is used to lift a load of 550 kg.   The square…

A: m = 550 Kg W = 550 × 9.81 = 5395.5 N Pitch P = 3mm Diameter d = 15 mm Coefficient of friction µ =0.2…

Q: A truss structure subjected to a vertical load of 10000 N is shown in the figure. Using finite…

A: To solve this problem using the finite element method, we need to discretize the truss structure…

Q: 3. Petrol is drained from a tank X to tank Y via pipeline A-B (see figure Q3). A pump is then used…

A:

Q: At a larger radius the rate of shear strain is 18 s-1 and the consistency coefficient is 0.6 Pa s.…

A: Given:Rate of shear strain, γ=18 s-1Consistency coefficient, k=0.6 Pa.sFind:The shear stress.

Q: A cylindrical specimen of cold-worked copper has a %CW of 20%. If its cold-worked radius is 6.4 mm,…

A: Given data:- Percentage of cold work (CW)=20 % cold-worked radius(Rf)=6.4 mm To find:- the radius…

Q: Example 1.3 The blades of a wind turbine turn a large shaft at a relatively slow speed. The…

A:

Q: Q2 A short cylindrical billet 16 mm diameter and 40 mm gauge length is elongated under tensile load…

A: Dear Student since you have posted a question with multiple sub-parts, but as per Q& A…

Q: 1- A 2 m long conical tube is fixed vertically with its smaller end upwards. It carries liquid in…

A:

Q: Machine setup steps should be stated in bullet points for ease.

A: To explain: Machine setup steps should be stated in bullet points for ease.

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.