How does the coupling factor affect the primary and secondary voltages? For example if the turns ratio in my transformer is 1:2 and the Vin is 10V, the voltage on the primary side is 10V and the voltage on the secondary side is 20V when the coupling factor (k) is 1. What will the primary and secondary voltages be if the coupling factor becomes 0.5?

How does the coupling factor affect the primary and secondary voltages? For example if the turns ratio in my transformer is 1:2 and the Vin is 10V, the voltage on the primary side is 10V and the voltage on the secondary side is 20V when the coupling factor (k) is 1. What will the primary and secondary voltages be if the coupling factor becomes 0.5?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.3P: Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source...

See similar textbooks

Similar questions

Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
The rated power of a certain transformer is 1 kVA. The transformer operates at 60 Hz and 120 V ac. at 60 Hz and 120 V ac. The secondary voltage is 600 V. (a) What is the maximum current at the load? (b) What is the smallest RL value that can be excited? (c) What is the largest capacitor that can be connected as a load?
8- The equivalent resistance of the primary of a transformer having K = 4 and RI - 0.1 ohm when referred to secondary becomes..ohm. a-0.1 b-0.01 c-0.004 d- 1.6
1. An ideal transformer with a 450 turn primary connected to a 600 V, 60 Hz supply line needs to output 240 V from the secondary. A 100 load is connected across the secondary. How many turns the secondary must have to output the desired voltage? What is the current through the load? What is the current drawn through the primary?
11- The output current corresponding to maximum efficiency for a transformer having core loss of 100 W and equivalent resistance referred to sccondary of 0.25 2 is .. ampere. a- 20 b-25 c- 5 d- 400
The equivalent resistance of the primary of a transformer having K = 2 and R1 = 0.2 ohm when referred to primary becomes.......ohm. Group of answer choices 0.05 2.5 0.02 0.004
all äabl (CME 446) 1 If F3=0.1 and Z3=45 Q, then the impedance of the next stage in the multi-section transformer is: of O a. 40.5 stion O b. 49.5 O C. 55 O d. None O e. 36.8 s page Next page
What is the turns ratio of the transformer needed to match a 1 k source resistance to a 160 load? A. 2.5:1 B. 0.4:1 C. 6.25:1 D. 16:1