i) The program has four errors. Identify and state how you would correct them. Briefly describe the behaviour of the program paying particular attention to the configuration and operation of Timer 0. ii) iii) Assuming the amended code is run on a classic 8051 using a 12 MHz crystal, estimate the period of the waveform on P1.0.

i) The program has four errors. Identify and state how you would correct them. Briefly describe the behaviour of the program paying particular attention to the configuration and operation of Timer 0. ii) iii) Assuming the amended code is run on a classic 8051 using a 12 MHz crystal, estimate the period of the waveform on P1.0.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

This question is from the subject Digital Logic Design. Assume your register number SF20-BEC-xxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary.b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SF20-BEC-156.
ehcu.org/pluginfile 100% 10 / 11 locations, count how many times is 0 and how many times 1 is. Questions:- 1- Write a program in assembly language to perform the following logic ci BL CL DL [5100]- 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , LG
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
1- Write a program in assembly language to perform the following logic ci CL DL [5100]– 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX, FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX,
An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
Draw logic diagram for half adder and full adder circuit using Logisim Software
Write assembly language program to substrate two 8 bit numbers and store the result on memory location 3500H. Also show data considered and result of program
6) Write an 8086 assembly language program to multiply the contents of the registers CL & BL by using repeated addition and store the result in AX. 0006
Which function performs the following operation? Give the assembly instruction and show your work.  Before A= 11011011, CF=1 After A= 10111101, CF=1
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
Please help me draw this demultiplexer using logic gates