If a moment, M=10 ft-kips, is applied to the cross-section about its strong axis, what is the maximum stress in the cross-section, and where would that stress occur? Utilize the values that you determined in Part (e). (h) If a moment, M=5 ft-kips, is applied to the cross-section about its weak axis, what is the maximum stress in the cross-section, and where would that stress occur? Utilize the values that you determined in part (e). (i) If the cross-section is made of Gr. A36 steel, would these moments produce linear or non-linear behavior in the cross-section? Why?

If a moment, M=10 ft-kips, is applied to the cross-section about its strong axis, what is the maximum stress in the cross-section, and where would that stress occur? Utilize the values that you determined in Part (e). (h) If a moment, M=5 ft-kips, is applied to the cross-section about its weak axis, what is the maximum stress in the cross-section, and where would that stress occur? Utilize the values that you determined in part (e). (i) If the cross-section is made of Gr. A36 steel, would these moments produce linear or non-linear behavior in the cross-section? Why?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
! Required information Consider the given state of stress. to A16 ksi 10 ksi Determine the normal and shearing stresses after the element shown has been rotated through 10° counterclockwise, using Mohr's circle. The normal stress ox'is ksi and oy'is |ksi. The shear stress Tx'y'is ksi.
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr 5600 Ksi. %3D %3D 3 ft 2 ft 0.5 in. 1 in. T = 50 lb ft
allowa quired wall thickness 2:11 .l 0.31 KB/S 64 Edit 16 A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E = 200 GPa. 36 mma 2 m OWhat is the displacement of the loaded end B of the bar? ® Determine the tensile stress induced in rod CD by the 80 kN load D If the allowable stress in rod CD is 124 MPa, what weight W can be safely 1.8 m 12m applied? w80 AN 1. A holl ow cir cular steel colum n is s ubjected toa compression load of 380 kN . The column has a length of 2.4 mn.and an outside dia meter of 187.5 mm. E - 200,000 MPa Determine the min. roquired wall thicknesss base on an allo wable com pressi ve stress of 48 MPa. Determine the min. required wall thickness based on 30 MPa. Determine the min. required wall thickness based on the allowable shortening of the colum n to b e 0.5 0 mm- allowable shear stress of C3D P-38 O kN 2.4 m 2. An 8 mm diameter steel rod, 20 m. long…
The rigid bar AD is supported by two steel wires of 1.5 mm diameter (E = 200 GPa) and a pinand bracket at D. Knowing that the wires were initially taut, determine the stress in each wirewhen a 1200 N load P is applied at D. What is the corresponding deflection of point D?
The beam has a rectangular cross section and is subjected to the loading shown. Determine the components of stress ox, oy, and Txy at point B. 800 N B 1000 N 15 mm 20 mm 20 mm 15 mm 100 mm 10 mm
The strain in the x direction at point A on the A-36 structural-steel beam is measured and found to be εx = 217 x 10^6. Determine the applied load P. What is the shear strain γxy at point A?
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress iss =10 MPa. 500 N/m 1.5 b OB - x m 2 m 2 m Calculate the centroid of the cross section of the beam O (1.5b, 1.5b] O (1.5b/2), (1.5b/2)] O (0.(1.5b/2)] O (0,0) [(1.5b/2), 0] O (0, 1.5b)
QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the cross section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm y 10 mm At-40 mm-- 30 гу 30 mm 10 mm 10 mm
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! For the frame shown, a 4QQT-N load is acting on member ABD at D. If the allowable material shear stress for is 4Q MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.