If the 18 mm plate is connected to two cover plate of 10 mm on top and bottom, what is the capacity of the connection in double shear? Assume that the shear planes pass though the threaded portion. State the condition necessary for these strengths to be available. (Draw the connect first and calculate the capacity)

If the 18 mm plate is connected to two cover plate of 10 mm on top and bottom, what is the capacity of the connection in double shear? Assume that the shear planes pass though the threaded portion. State the condition necessary for these strengths to be available. (Draw the connect first and calculate the capacity)

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.12.1P

See similar textbooks

Similar questions

The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for the bolts is 100 MPa. Assume each bolt supports an equal portion of the load. Determine the required diameter of the bolts. a. 20.6 mm b. 25.2 mm c.35.7 mm d.17.8 mm choose letter of correct answer
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
For the bracket connection shown in the figure, determine the design strength in kips of the connection
A rigid bar AC is supported pinned supported at A and bar DB at B. See typical bolt connection detail. A concentrated weight, denoted as W is attached at the end of the rigid bar. L1 = 2.6 m L2 = 2.1 m H= 1.2 m W= 14 KN What is the required diameter of the bolt (in mm) at connection B given the allowable shearing stress to be 40 MPa ? Consider single shear. L1 L2 A B C H D इस W CONNECTION AT B
A welded bracket connection is shown in figure. It supports a factored load of 150 kN at a distance of 120 mm from the face of column. Design the fillet weld on two sides. Grade of steel = Fe410, f. = 250 MPa. y 120 mm P₁ = 150 kN Fillet weld t = 12 mm
Two 75mmx8mm A36 steel plates are welded in a 10mm gusset plate. Assume a weld thickness of 7.5mm and that of electrode used is E70. Determine the following: 1. Total Length of weld if P=300KN 2. Load P based on block shear if L1=85mm and L2=92mm. Neglect end returns P -2-75mmx8mm plates 10mm-thk L1 gusset plate L2 end returns
In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to a 16 mm gusset plate for a tensile load of 650 kN. Design the moment free welded connection. The distances of centroid of angle from the back side of legs are C₁=C₁ = 30.9 mm. The strength of the weld per mm thickness per mm length is 76 MPa.
STAGGERED CONNECTIONS: A PLATE WITH WIDTH OF 400 mm AND THICKNESS OF 12 mm IS TO BE CONNECTED TO A PLATE OF THE SAME WIDTH AND THICKNESS BY 34 mm DIAMETER BOLTS, AS SHOWN IN THE FIGURE. THE HOLES ARE 2 mm LARGER THAN THE BOLT DIAMETER. THE PLATE IS A36 STEEL WITH YIELD STRENGTH Fy = 248 MPa. ASSUME ALLOWABLE TENSILE STRESS ON NET AREA IS 0.60Fy. IT IS REQUIRED TO DETERMINE THE VALUE OF b SUCH THAT THE NET WIDTH ALONG BOLTS 1-2-3-4 IS EQUAL TO THE NET WIDTH ALONG BOLTS 1-2-4. a. CALCULATE THE VALUE OF b IN MILLIMETERS. b. CALCULATE THE VALUE OF THE NET AREA FOR TENSION IN PLATES IN SQUARE MILLIMETERS. c. CALCULATE THE VALUE OF P SO THAT THE ALLOWABLE TENSILE STRESS ON NET AREA WILL NOT BE EXCEEDED.
2. A staggered riveted connection has rivets arranged as shown. Diameter of rivet is 28 mm. Use AISCINSCP Specs. Fy 248 MPa, Fu = 400 MPa. Determine the distance "S" so that the area area in chain ABCD is equal to the net area in chain ABD. Determine also the tensile capacity of P. 45 10 350 mm 90 90 I mm 60 mm 888
Six rivets are used in the connection shown in the figure. If both P=50KN, what is the minimum diameter rivet is necessary so as not exceed the 70MPa allow shearing stress? What thickness of plate is required so as not exceed a bearing stress of 140MPA? p= 50 80 mm 80 mm 100 mm
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
What is the safe load "P" that can be transmitted by the fillet-weld joint shown in figure below if allowable shear stress in the fillet weld is 108 MPa and F.O.S. for load is 1.5? P4 www 60mm 777 50mm 8mm P