In an EAS Reaction the compounds 5.0g of acetanilide, 0.2g potassium bromate, 5ml acetic acid, 0.9 ml hydrobromic acid solution, and 5 ml saturated sodium bisulfite solution are used. Given these compound and obtaining a yield for the experiment at 6.3 grams which yields 5.3 grams after recrystallization and drying, Please find the theoretical yield and the percent yield?

In an EAS Reaction the compounds 5.0g of acetanilide, 0.2g potassium bromate, 5ml acetic acid, 0.9 ml hydrobromic acid solution, and 5 ml saturated sodium bisulfite solution are used. Given these compound and obtaining a yield for the experiment at 6.3 grams which yields 5.3 grams after recrystallization and drying, Please find the theoretical yield and the percent yield?

Macroscale and Microscale Organic Experiments

7th Edition

ISBN:9781305577190

Author:Kenneth L. Williamson, Katherine M. Masters

Publisher:Kenneth L. Williamson, Katherine M. Masters

Chapter7: Extraction

Section: Chapter Questions

Problem 1Q

See similar textbooks

Similar questions

How many grams of NaAsO, should be weighed out to prepare a stock solution of 100 mg/L in 500 mL deionized water. Use the stock solution to prepare 4 different standard solution that can be used to prepare an analytical calibration curve to measure the concentration of 750 sample in the concentration range of 10-35 mg/L. Draw a proposed calibration curve (based on the results you achieved).
A Grignard synthesis begins with 10 ml of 3 M Phenylmagnesium Bromide and 1 grams of Methyl Benzoate, the 2.56 g of triphenylmethanol. What is the theoretical and percent yield of the reaction? Assume standard workup.
2.1g of sample are dissolved in methylene chloride and the sample is extracted with aqueous solutions of acid and base. Three compounds are isolated - 0.8g of ethyl p-aminobenzoate, 0.6 g of acetanilide, and 0.5 g of benzoic acid. Calculate the % recovery for the procedure. (Round the answer to the nearest tens place.) Give just the number, not a % sign.)
Three sample, X (neutral), Y (basic), and Z (acidic), were mixed and dissolved together in dichloromethane. Propose a method to separate all given sample individually using the combination of liquid-liquid extraction, crystallization, distillation, and sublimation technique.
A student reacted 0.500 g of triphenylmethyl bromide and 20.0 mL of water in 10 mL of acetone. The crude product was collected and dissolved in 35 ml of hot isopropanol. The hot solution was transferred immediately to an ice bath, then vacuum filtered. a) 0.024 g of purified solid was collected. What was the percent yield? b) state two specific reasons for the student's low yield based on the described procedure above.
A 532 mg of a mixture of fluorene and benzoic acid was weighed out and subjected to an extraction and recrystallization. After this purification was completed the product crystals were dried and analyzed. The purification procedure produced 174 mg of fluorene and 249 mg of benzoic acid. Calculate the percent composition of this mixture.
Write TRUE if the BOLD word/phrase makes the statement correct. Otherwise, write the correct WORD/PHRASE that will make the statement true. If there are two bold words/phrases in a number, write your answer for EACH of the bold words/phrases. 1. The addition of excess charcoal would decrease the % recovery in the purification by recrystallization. 2. If the target compound is contaminated with impurity, the melting point will be higher than the theoretical value and the melting range is large.
1,4‐Dimethoxybenzene (0.642 g) was dissolved in 2.0 mL acetic acid in a 25 mL Erlenmeyer flask using heat from a hot plate. Once the solid dissolved, 1.0 mL tert‐ butanol was added, and the reaction mixture was cooled in an ice bath. Then 2.0 mL concentrated sulfuric acid was added in 2‐3 drop portions,stirring the mixture after each aliquot. After the addition, the flask was removed from the ice bath and allowed to sit at room temperature for 15 minutes. Then 1.0 mL water was added dropwise to dilute the acid and the reaction mixture was added to 40 mL cold water in a 100 mL beaker. The solid was vacuum filtered and washed with 5 mL cold water, giving 52 g filtrate. The product wasrecrystallized from 4.5 mL methanol, yielding 0.317 g purified 1,4‐di‐tert‐butyl‐2,5‐dimethoxy benzene (27.2% yield). What is the atom economy, e-factor, and effective mass yield?
In a Grignard reaction, 1.4555 g phenyl bromide, 10. g carbon dioxide, 0.5734 g magnesium filings, and 30.2 mL of 6M HCl were used but only 573 mg of benzoic acid were isolated after recrystallization? what was the percent yield for the overall process? Give the answer to the nearest whole number please
What is the theoretical yield and limiting reagent for the reaction of benzophenone with sodium borohydride to form diphenyl methanol as described in the experiment provided if you begin with 1.75g of benzophenone in 25 mL of 95% ethanol and add 0.75 g of sodium borohydride portion wise over 45 minutes?
Tom, an analytical chemist, bought a bag of decaffeinated coffee from a grocery store. However,Tom suspected that he might have received regular coffee and therefore decided to analyze hiscoffee for caffeine. In the lab, he took 0.5 mL of the brewed coffee and diluted it in water tomake a 100.0 mL solution. He performed four analyses and found the concentrations to be 4.69,3.99, 4.12, and 4.50 mg/L, respectively. (Assume the density of all solutions is 1.000 g/mL,1oz= 28.35 mL).(a) Report the concentration (in mg/L) of caffeine in the brewed coffee using the format asaverage ± standard deviation. (Note this is not the concentration in the diluted solution.)(b) Look up the caffeine content of regular vs. decaffeinated coffee. Do you think that Tom wasgiven the wrong type of coffee?(c) Caffeine intake of 300 mg per day reportedly has no adverse effects in the vast majority ofthe adult population. If Tom drinks 3 cups (8 oz/cup) of this coffee daily, is his intake withinthis known safe…
How would each of the following errors affect the experimental value of your molarity of acetic? Would your Molarity value be too high, too low, or unaffected? Explain your answer. if you titrated your acid sample to a bright pink rather than faint pink endpoint? if your "acetic acid" burette was still wet inside with deionized water when you filled it with acetic acid? if you recorded the final volume of NaOH as "39.88 mL" instead of "38.88 mL"?