in As in Example 2.5, a balanced-Y-connected voltage source with Eab = 480/0° volts is applied to a balanced-A load with ZA = 30/40° 2. The line impedance between the source and load is ZL = 1/85° for each phase. Calculate the per-unit and actual current in phase a of the line using Stase3 = 10 kVA and VbaseLL = 480 volts. %3D Z. C a Eon Eun Z, = + b. Z = 1/85° 2

in As in Example 2.5, a balanced-Y-connected voltage source with Eab = 480/0° volts is applied to a balanced-A load with ZA = 30/40° 2. The line impedance between the source and load is ZL = 1/85° for each phase. Calculate the per-unit and actual current in phase a of the line using Stase3 = 10 kVA and VbaseLL = 480 volts. %3D Z. C a Eon Eun Z, = + b. Z = 1/85° 2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.22MCQ: In a balanced three-phase Y-connected system with a positive-sequence source, the line-to-line...

See similar textbooks

Similar questions

2) The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S2=15.93 MW - j33.4 Mvar, and at bus 3 is S3-77 MW + j14 Mvar. It is required to hold the voltage at bus 3 at ...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu S₂ Figure V3 S3
2. The one-line diagram of a three-phase power system is as shown in the figure below. Impedances are marked in per unit on a 100-MVA, 400-kV base. The load at bus 2 is S2 = 15.93 MW-j33.4 Mvar, and at bus 3 is S3 = 77 MW +j14 Mvar. It is required to hold the voltage at bus 3 at 4006 0 kV. Working in per unit, determine the voltage at buses 2 and 1. V3 j0.5 pu V₂ S₂ j0.4 pu S3
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
In Figure 1, the 3-phase source has a line-to-line voltage of 440 volts. The details of the impedances are the following: Z₁ = 36-j15; Z₂ = 40 + /300; Z₂ = 45+j60 ; Z₂ = 75 + jo ; Z5 = 50+j50; Z6 = 20+ j48 2. Determine the following: (a) Line currents: labi, and I (c) Line currents: lar, Ibr, and ICT; (b) Line currents: Iaz, Ibz, and Iczi (d) PT, QT, ST, and pft for the system; (e) W, and W, readings for 2-wattmeter method at lines a and b. Balanced 3-Phase ab-bc-ca source C Figure 1 →laT -Ibr -KT 1 lal ²3 ↓ Ibi 1 Ici la2 lb2 le2ܝ 150 1²₂ OND
Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR
Problem 4- A large 3-phase industrial load draws 3.6 MVA at 0.85 power factor lagging from through a three- phase 12.47/7.2 kV 3-wire overhead distribution line. The phase conductor is #1 ACSR “Robin". Taking 3.6 MVA and 12.47 kV as base values, determine (a) The base impedance in (N) (b) The reactive power drawn by the load (p.u.) (c) The total current (p.u.) drawn from the power supply
The impedance per phase of 3-phase transmission line on a base of 100 MVA, 100 kV is 2 pu. Find the value of this impedance on a base of 400 MVA and 400 kV would be..
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
2.21 The three-phase source line-to-neutral voltages are given by E = 10/0°, Em = 10/+240°, and En = 10/-240 volts. Is the source balanced? (a) Yes (b) No In a balanced 3-phase wye-connected system with positive-sequence source, the line- to-line voltages are v3 times the line-to-neutral voltages and lend by 30. (a) True 2.22 (b) False 2.23 In a balanced system, the phasor sum of line-to-line voltages and the phasor sum of line-to-neutral voltages are always equal to zero. (a) False (b) True 2.24 Consider a three-phase Yconnected source feeding a balanced-Y load. The phasor sum of the line currents as well as the neutral current are always zero. (b) False (a) True 2.25 For a balanced-A load supplied by a balanced positive-sequence source, the line cur- rents into the load are v3 times the A-load currents and lag by 30°. (a) True A balanced A-load can be converted to an equivalent balanced-Y load by dividing the A-load impedance by (a) V3 When working with balanced three-phase circuits,…
2.41 A A-Y connected bank of three identical 150-kVA, 2400-V:120-V, 60-Hz transformers is supplied at its high-voltage terminals through a feeder whose impedance is 6.4+j154 m2 per phase. The voltage at the sending end of the 2.12 Problems 119 feeder is held constant at 2400 V line to line. The results of a single-phase short-circuit test on one of the transformers with its low-voltage terminals short-circuited are VH = 131 V 1y = 62.5 A P= 1335 W %3D a. Calculate the series impedance of this three-phase transformer bank as referred to its high-voltage terminal. b. Determine the line-to-line voltage supplied to the feeder when the transformer bank delivers rated current at rated voltage to a balanced three-phase unity power factor load at its low-voltage terminal.
The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S-15.93 MW-j33.4 Mvar, and at bus 3 is S3-77 MW+j14 Mvar. It is required to hold the voltage at bus 3 at...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu $₂ Figure V3