In the connection shown in Figure 5, ASTM A572 Grade 50 steel is used for tension member (C10-20), A36 steel is used for the gusset plate (t = ½ in.). The holes are for 1-inch bolts. What is the maximum factored block shear strength in LRFD for this connection? Note: You must check both, the tension member and the gusset plate, for block shear. いだ 2" -1'" C10x20

In the connection shown in Figure 5, ASTM A572 Grade 50 steel is used for tension member (C10-20), A36 steel is used for the gusset plate (t = ½ in.). The holes are for 1-inch bolts. What is the maximum factored block shear strength in LRFD for this connection? Note: You must check both, the tension member and the gusset plate, for block shear. いだ 2" -1'" C10x20

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.1P

See similar textbooks

Similar questions

For the splice connection shown in the figure, a. Check all spacing and edge-distance requirements. (For 1-in diameter bolts minimum edge distance is 1.25 in. AISC Table J3.4) b. Compute the design strength based on shear and bearing. (Use LRFD) The plates are PL 1/2" x 7" steel ASTM A36 (Fy = 36 ksi, Fu = 58 ksi) and the bolts are 1-in diameter A325X (Fnv = 60 ksi) in standard holes.
The butt connection shows 8-22 mm diameter bolts spaced as shown below. P- 50 100 50 50 100 50 16 mm +HHHH 40 80 40 12 mm Steel strength and stresses are: Yield strength, Fy = 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Based on the gross area of the plate. Based on the net area of the plate. Based on block shear strength. Bolt hole diameter = 25 mm Calculate the allowable tensile load, P, under the following conditions:
Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The angle is ASTM A36 steel. X = 0.7 Y = 3.8 Z=1/2 Round your answer to 2 decimal places. Your Answer: Incorrect The answer is 77.15 ± 1%. 1/2" X" bolts 1½" Gusset plate -L3 X 3 X Z Tu I
Two steel plate tension members have been connected using 0.72” diameter bolts arranged in an equally-spaced four by four square formation.Total plate self-weight is specified as 912 pounds.Design of the elements adhered to the set of values that are twice as much as the minimum requirements. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 54ksi and the min required edge distance as 0.125ft. a)Sketch the connection showing all the details and measurements with units. b)Find the maximum allowable service dead load(excluding the self-weight)and live load assuming live load is half as much as dead load including the self-weight of the plates.
Two plates each with thickness t = 10 mm are bolted together with 6 - 16 mm diameter bolts forming a lap connection. Plate (A36): Fy = 248 Mpa FU = 400 MPa bolts are A325 in standard holes with threads excluded from shear planes. Considering Tension Yielding, compute the the design strength for LFRD. Use NSCP 2015 Round your answer to 2 decimal places.
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for block shear in kip? Express your answer in two decimal places. 2" 3" 2" 1/2" thick Gusset Plate O 2" 3" 3" 2" 3/8" thick P
The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for tension on gross area in kip? Express your answer in two decimal places. 1/2" thick Gusset Plate 3/8" thick 2" 3" 2" 2" 3" 3" 2" P.
4. Determine the design strength of the connection shown in the Figure below. Thebolts are 25 mm diameter A490 bolts with the threads not in the plane of shear.A36 steel is used (Fy = 250 MPa, Fu = 400 MPa).a. Compute the shear strength for all bolts.b. Compute the bearing strength for the tension member on all bolts.c. Compute the bearing strength for the gusset plate on all bolts.d. Compute the tensile strength of the tension member.e. Compute the design strength of the connection.
3. Determine Rn based on bolt limit states. Slip critical connection is used for design and Grade 10.9 M22 Bolts with Class A surface. Check minimum edge distance and spacing with TSSDC 2016. All members are $355. There is no filler between plates and Du=1.0. Fy= 355 MPa; Fu=510 MPa; E=200000 MPa. All units are in mm. $R.=? 100 100 O 60 Geset Plate 75 Plate Gusset Plate $R.=? *20*201 Plate
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for block shear in kip? Express your answer in two decimal places.