In the figure, you see a person with a body mass of 84kg and height of 1.79m holding a warrior 3 yoga pose. For the total leg extended in the air (greater trochanter to medial malleolus), calculate the moment at the hip about the z axis that must be generated to maintain this position for the extended leg only. Enter your answer in Nm and be sure to account for the appropriate direction of the moment using (+ or -) in your answer. y

In the figure, you see a person with a body mass of 84kg and height of 1.79m holding a warrior 3 yoga pose. For the total leg extended in the air (greater trochanter to medial malleolus), calculate the moment at the hip about the z axis that must be generated to maintain this position for the extended leg only. Enter your answer in Nm and be sure to account for the appropriate direction of the moment using (+ or -) in your answer. y

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.8P: The figure models the handle of the water cock described in Prob. 4.9. Draw the FBD of the handle,...

See similar textbooks

Similar questions

PROBLEMS Introductory Problems 2/111 The weight of the computer system is 80 lb with center of gravity at point G. Determine the moment Mo of this weight about point O on the horizöntal table top. Find the magnitude of Mo. -320i + 160j lb-ft, Mo Ans. Mo = 358 lb-ft 1. 48" 9" 24"
2) Determine the support reaction forces and moment for the 3a sketched system.
Find box for the given Plane, where by =120m, d=25m, bz=25m, d2=100m, b3=80m & d3=25 m (Enter only the values in the boxes by referring the unit given in brackets. Also upload your hand written answers in the link provided) b2 dz di bị The value of X= (unit in m) The value of Y= (unit in m) The moment of inertia for sec 1 = lyyi = (unit in m) The moment of inertia for sec 2 = lyy2 = (unit in m4) The moment of inertia for sec 3 = lyya = (unit in m4) The moment of inertia of the given plate = lyy = (unit in m)
At the shown position, the ground reaction forces measured using a force platform are 600N in the vertical direction (Fy) and 200N in horizontal direction (Fx). The mass of the limb below the knee is 4kg with the centre of gravity at the point G. Determine the forces and moment applied to the knee joint. Draw correct free body diagram using any part of the body shown below.
I'm stuck at establishing the Moment at O for both circles. I don't know how to find the force.
6 in 60° 20 in Statics Instructor A vertical force of P = 100 lb is required to remove the nail at C from the board. Determine the magnitude of the moment about B exerted by the 100 lb vertical force. Draw a free body diagram for the system. Then, use what you know about moments to solve for Mp What is the magnitude of the moment at point B due to P if P = 100 lb and 9 = 10"? Round to the nearest whole number. Enter a response then click Submit below lb in
In the figure, the engine of a vehicle is shown as a representation.The crankshaft of the engine around the x-axis It rotates at 4000 rpm and its moment of inertia is 0.5 kgm2.Moving in the y direction, the vehicle enters the curve with a radius of 70 m at a speed of 120 km/h. In the meantime, find the moment coming to the motor bearings and interpret its effect on the vehicle.
In the figure, the engine of a vehicle is shown as a representation.The crankshaft of the engine around the x-axis It rotates at 4000 rpm and its moment of inertia is 0.5 kgm2 .Moving in the y direction, the vehicle enters the curve with a radius of 70 m at a speed of 120 km/h. In the meantime, find the moment coming to the motor bearings and interpret its effect on the vehicle.
For the pipe frame pictured below: Replace all forces and the couple by the equivalent resultant force R acting on point O and a couple Mo (written as vectors) Describe this system as the wrench, resultant force R and wrench moment M (written as vectors) Specify the coordinates of the point, P in the x-y plane, through which the line of action of the wrench passes (x,y) (Hint: Watch your units for each term and directions as you calculate moments) 55 lb 25° 11" 40 lb 60 lb-f 80 lb 17" 14" X y
The figure models the handle of the water cock described in Prob. 4.9. Draw the FBD of the handle, neglecting its weight. Count the unknowns.
Construct the shear force and bending moment diagrams for the beam shown by the area method. Neglect the weight of the beam.
For the position vectors P and Q shown, determine the orthogonal component of P Ă— Q in the direction of OA.