It is required to design the common-source amplifier below to provide a gain of -20 V/V. It is given that gm3 = 3.63 mA/V, (W/L)1 = 50, (W/L)2 = 60, (W/L)3 = 110, VAn = 10 V, VAp = 5 V, and.µA/V2 %3D %3D %3D %3D %3D %3D (a) Find the transconductance parameter gm3- (b) Find the DC bias current Ip. (c) Find the reference current IREF. Hint: A, = -9m3 (ro2 || ro3) %3D Im = 21th Cox () ID %3! VDD Q2 Q1 Ip IREF Q3 Insert the DC bias current, Ip, in mA below:

It is required to design the common-source amplifier below to provide a gain of -20 V/V. It is given that gm3 = 3.63 mA/V, (W/L)1 = 50, (W/L)2 = 60, (W/L)3 = 110, VAn = 10 V, VAp = 5 V, and.µA/V2 %3D %3D %3D %3D %3D %3D (a) Find the transconductance parameter gm3- (b) Find the DC bias current Ip. (c) Find the reference current IREF. Hint: A, = -9m3 (ro2 || ro3) %3D Im = 21th Cox () ID %3! VDD Q2 Q1 Ip IREF Q3 Insert the DC bias current, Ip, in mA below:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Hello. The answers I got for this are pf distortion = .83 and pf total of 0.7. I'm not sure I did it right though and I was hoping to compare answers and see how you go through this. Thank you.
In a summing inverting amplifier,Rf is 100k ohms, V1 is a sinusoid with 2V amplitude and frequency of 1Hz ,R1 is 10k ohms, V2 is a sinusoid with 3V amplitude and frequency of 1Hz, and R2 is 10k ohms. Vs+ = 18 V and Vs- = ground. What is the output voltage? Please draw the waveform as well.
this is CC(common collecter ) amplifier.why it is a cc circuit, you can get the answer from its AC circuit.so now PLS draw its AC and DC circuit. plz solve it early
Derive the transfer function of the system shown in figure c. Page 2 of 3 R Figure (e)
VoD +12 V For the circuit of the adjacent figure a) Given that Ip = 2.83 mA, VGS(om=-7 V and Ipss = 8 mA , find VDs and VGs.. b) If a 50 mV rms input signal is applied to the amplifier, what is the peak-to-peak output voltage? gm = 5000 µS. c) Calculate the output resistance. %3D Ro 10AF 0.1 uF R 10 L. Ra 10 MA 10kn ID= 2.83 mA, Vas (Oef)=-7V. %3D
ression.. A noninverting amplifier has an Ri of 1.0 kn and an Rf of 100 kn. Determine Vf and B if Vout=5 10 my ras R₂ 560 kn R₁ 1.5 kn (Ctrl)
4) +20 V For the depletion type MOSFET network in the figure: 1.5 k2 a) Find ID, VD, and VGs. Ipss = 8 mA V = -4 V b) Show ID, and VGs on the transfer characteristics. 100 M2
Shown below is a PNP CE amplifier with large AC coupling capacitors Cx and Cy with: Q1 has the following : VeB,Q = 0.7V, Vec,SAT = 0.2V, PNP Q1 VA → 00 Cx Rin Rx vin vout B = 100. Vr = 0.026V| 5k 430k Ry Rz 5k 5k Find Ico, VEc,Q, 9m1,rn1, Gm, Ro, Ay
Qustion 3, ANALISIS AC The following amplifier (consider the case with a load RL ) consists of a n channel JFET. In the amplifier the value of the source DC (+VDD= 20V) and of all the resistors (shown in the schematic) and capacitors (C1=C2= 20 uf) is known. At the same time, the JFET has the following specifications: IDSS = 10 mA and VP= -3.5 V.The output resistance of the JFET is rd= infinity Ω (INFITY OHM).AC analysis:The input signal Vs is a small sinusoidal signal, at the same time it oscillates at a medium frequency, in such a way that the response is not affected by the capacitances. Get the circuit in small signal and do all the necessary procedure / demonstration. To determine:A) The transconductance gm at the point of operation.B) The small signal equivalent circuit drawn conveniently.
We examined the common source amplifier shown in the figure in the 5th experiment. The selection criterion of the input capacitance is Xcin = 0.1Rin: Calculate the required input capacitance value, Cin , if an input signal with a frequency of 2 kHz is applied. Şekitde gösterilen ortak source yükseltecini 5. deneyde incelemiştik Giriş kapasitesinin seçim kriteri Xcin - 0.1Rin dir. 2 kHzlik giriç sinyali için gerektt tapasite, Cm değerini hesaplayınız. Circuit parameters / Devre Parametreleri R1 = 53 k2, R, = 17 k2 R1 RD Cout Vout D VDD M2 Cin G Vin R2 RS cs O a. 74.19 nF O b. 86.55 nF O c. 49.46 nF O d. 61.82 nF O e. 43.28 nF
Given the circuit below, please solve for the ff: a. What is the configuration of the given amplifier circuit below?b. How are the coupling capacitors treated in the figure at AC?Please show your clean and complete solution
1. For the following circuit rsuming ideal OpAmp, what resistor is needed for Rf to have a gain of 5 from Vo to Vi? (ì Vo 2kQ IDEAL if 3kQ