l TEW 9:44 AM 1) A box of mass m= 12kg lies on a flat surface. The coefficient of static friction is Hs = 0.50 and the coefficient of kinetic friction is µk = 0.30. Make sure you get the correct normal force for the situation at hand. It does not have to be equal to mg. a) How large should the force be to get the box moving? b) Once it is moving with this force, what is the acceleration of the box?

l TEW 9:44 AM 1) A box of mass m= 12kg lies on a flat surface. The coefficient of static friction is Hs = 0.50 and the coefficient of kinetic friction is µk = 0.30. Make sure you get the correct normal force for the situation at hand. It does not have to be equal to mg. a) How large should the force be to get the box moving? b) Once it is moving with this force, what is the acceleration of the box?

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter6: Applications Of Newton's Laws

Section: Chapter Questions

Problem 82P: To maintain a constant speed, the force provided by a car’s engine must equal the drag force plus...

See similar textbooks

Similar questions

A 0.400-kg pendulum bob passes through the lowest part of its path at a speed of 3.00 m/s. (a) What is the tension in the pendulum cable at this point if the pendulum is 80.0 cm long? (b) When the pendulum reaches its highest point, what angle does the cable make with the vertical? (c) What is the tension in the pendulum cable when the pendulum reaches its highest point?
A 50.4 N force is applied to keep a blok of 24. 2 N on the side wall. The static and the kinetic friction coefficients are given as 0.60 and 0.40. Assume the blok is relased from stationary state, (.) a. Does the block start to move? b. What force the wall apply to the block?
A block of mass M slides () along a rough (s) inclined surface (dila au) with a constant velocity. The inclination angle ( ) of the surface is 0 as shown in the adjacent figure (sl ). The coefficient (Jales) of kinetic friction ( Hk) of the inclined surface is: A. cos?(0) B. cos(0) C. sin(20) D. tan(0) E. sin(0) M V= Constant 10 *Take g= 9.8 m/s?
1 V:IV H.W.docx H.W: Two boxes are connected by a cord running over a pulley. The coefficient of kinetic friction between m, (5kg) and the table is 0.20. We ignore the mass of the cord and pulley and any friction in the pulley, which means we can assume that a force applied to one end of the cord will have the same magnitude at the other end. We wish to find the acceleration, a, of the system, which will have the same magnitude for both boxes assuming the cord doesn't stretch, As m (2Kg) move down, m,move to the right. m. د قوة الشد Tو تسارع النظام .a علما بأن البكرة مهملة الكتلة والاحتكاك؟ 出 1
1 V:IV H.W.docx H.W: Two boxes are connected by a cord running over a pulley. The coefficient of kinetic friction between m, (5kg) and the table is 0.20. We ignore the mass of the cord and pulley and any friction in the pulley, which means we can assume that a force applied to one end of the cord will have the same magnitude at the other end. We wish to find the acceleration, a, of the system, which will have the same magnitude for both boxes assuming the cord doesn't stretch. As m; (2Kg) move down, m, move to the right. m. د قوة الشد Tو تسارع النظام .a علما بأن البكرة مهملة الكتلة والاحتكاك؟ 出 l20 Son la 1
A block of mass M slides () along a rough (s) inclined surface (Ji zlaw) with a constant velocity. The inclination angle ( j) of the surface is 0 as shown in the adjacent figure ( l JKul). The coefficient (Jalea) of kinetic friction ( ) of the inclined surface is: A. cos'(e) B. tan(e) C. sin(20) D. cos(e) E. sin(0) V- Constant *Take g= 9.8 m/s²
The force needed to get a block moving and to just barely keep it moving were used to calculate the coefficient of static friction and the coefficient of kinetic friction for the block. Which values are most likely the correct ones for this block? O .35 for coefficient of static friction and .35 for coefficient of kinetic friction 25 for coefficient of static friction and .35 for coefficient of kinetic friction 35 for coefficient of static friction and .25 for coefficient of kinetic friction 25 for coefficient of static friction and .25 for coefficient of kinetic friction
A box of mass M = 50 kg rests on a rough (ji) horizontal surface. When a force F = 300 N is acted on the box as %3D %3D shown in the figure below, the box becomes on the verge of slipping (Y alig de j gainall ). The coefficient of static friction of the rough surface is: F A. 0.92 B. 0.75 40° C. 0.14 D. 0.57 E. 0.34
A block has a mass of 20kg rest initially on a plare inclined at 30 deg. What value of force is required to stop the block from sliding if: A. The plane has a coefficient of friction of static and kinetic equal to 0.16 and o.13 respectively. B. What will be the value of the force if the velocity is constant and is directed upward parallel to the inclined?
The forces are in static equilibrium. The 140 lb force is directed along the x-axis and the 300 lb force is directed along the negative z- axis. Determine the magnitude of the unknown force, R. Z X R Ox лог 140lb A (-50, 80, 160) lb By 300 lb у
A 2.00-kg block is at rest on a horizontal plank that is 1.50 m long. When one end of the plane is raised to 0.50 m, the block starts sliding down. What is the coefficient of static/starting friction between the block and the plank? O 0.43 O 0.35 0.33 O 0.53
e.co CU ct sona- n ect Pool artment... W 24,919 8. A mass m₁ = 9.00 kg is connected by a light string that passes over a pulley of mass M = 14.0 kg to a mass m₂ = 12.5 kg sliding on a horizontal frictionless surface (see figure). There is no slippage between the string and the pulley. What is the magnitude of the tension that is acting on mass m₂? (The moment of inertia of the pulley is ½/Mr².) N # 3 20 $ 4 R 999 F4 % 5 FS ^ 6 tv © MacBook Air Y & 7 m₂ F7 * 8 Dall 1 ( 9 M m₁ A 02 DD ) 0 P ISULI H by mi 04 M vauies or roe puffer