Let's assume that the outdoor temperature in your region was 1 C on 26.12.2002. Let's assume that you use a 2088 W heater in the room in order to keep the indoor temperature of the room at 20 ° C. In the meantime, a 68 W light bulb for lighting, a computer you use to solve this question and load it into the system (let's assume it consumes 217 W of energy), you and your two friends (three people in total) are in the room to assist you in solving the questions. A person radiates 45 J of heat per second to his environment. When you consider all these conditions, calculate the exergy destruction caused by the heat loss from the exterior wall of your room.

Let's assume that the outdoor temperature in your region was 1 C on 26.12.2002. Let's assume that you use a 2088 W heater in the room in order to keep the indoor temperature of the room at 20 ° C. In the meantime, a 68 W light bulb for lighting, a computer you use to solve this question and load it into the system (let's assume it consumes 217 W of energy), you and your two friends (three people in total) are in the room to assist you in solving the questions. A person radiates 45 J of heat per second to his environment. When you consider all these conditions, calculate the exergy destruction caused by the heat loss from the exterior wall of your room.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.63P

See similar textbooks

Similar questions

In a concentrated solar power plant, molten salt tank is used to store the thermal energy from the sun during the day. The tank wall thickness is 3cm containing molten salt at a temperature of 390 degree Celsius. There is atmospheric air outside the tank at a temperature of 30 degree Celsius. Suppose heat is lost as a result of heat transfer from the molten salt to the atmospheric air. What is the mode of heat transfer in this condition? conduction then convection convection then conduction convection then conduction then convection conduction then convection then conduction
The heat loss of a human body during stationary sitting is 400 kJ/H. A population of 800 if the ventilation system of the cinema hall is broken, after 15 minutes from the walls of the Hall considering that the heat loss is; a.) If the air in the hall is treated as a system, can you find an increase in the internal energy of the system? b.) If the air and people in the hall are treated as a system, the change in the internal energy of the systemdid you find it?
The left side of this equation tells how much energy Q the cylinder gives to the water while it cools. The right side of this equation tells how much energy Q the water and aluminum cup absorb from the cylinder to warm up. Because it is the same energy, they are equal. What is known in this equation? Mcyl 411.7 g, malum 46.5 g, malum+water = 175 g Can you find: mwater =? g Twater = Talum = 20°C (water and cup of room temperature) 90°C, T; = 35°C (hot cylinder and cool "cylinder+cup+water" temperatures) Tcyl kCal Calum = 0.22, Cwater 1 (specific heat of water and aluminum, measured in units kg-°C What are we looking for is Ccul - How we find it? Plug all the numbers into the equation (1), Ccul will be one unknown which you can calculate from the equation. Important, convert all the masses from grams to kilograms! After you find Ccyl, compare it to known value for the copper 0.093(our cylinder is made out of copper). |Ceyl -0.093| % : · 100% 0.093
a. A slab of thermal insulator is 100 cm² in cross section and 2 cm thick. Its thermal conductivity is 2.4 x 10 -+ cal/(s cm C"). If the temperature difference between opposite faces is 180 F', how much heat flows through the slab in one day?
A hot water leak in one of the faucets of your apartment can be very wasteful. A continuous leak of one quart per hour (a "slow" leak) at 155 degrees°F causes a loss of 1.81 million Btu per year. Suppose your water is heated with electricity. a. How many pounds of coal delivered to your electric utility does this leak equate to if one pound of coal contains 12,000 Btu and the boiler combustion process and water distribution system have an overall efficiency of 28%? b. If a pound of coal produces 1.81 pounds of CO2 during the combustion process, how much extra carbon dioxide does the leaky faucet produce in a year
A solid rectangular parallelepiped is made of aluminum and is initially at 20 C. The base is a 2 cm by 3 cm rectangle and the height of the parallelepiped is 5 cm. The parallelepiped is now dropped into hot oil at 150 C. Find: a) the temperature of point P and b) the temperature of the center of the parallelepiped after 2 min of exposure to hot oil. Point P is located 1 cm above the center plane and 1 cm from each side
Qi: (50 marks) Find the total heat flux of the composite wall when: B KA = KC = KF = 15 m. K KB = KD = 10 m. K KE = KG = 20 %3D m. K D. Height of B = C = D 4 cm 3 cm 4 cm 6 cm Height of F = G AT = 30 K
Conduction Heat Transfer X material (a) material (b) . both (a) and (b) have the same thermal conductivity the temperature distribution is independent of thermal conductivity it's not that simple 9. Fin efficiency is defined as: • tanh (mL) (hP/k Ac)1/2 (heat transfer with fin) / (heat transfer without fin) (actual heat transfer through fin) / (heat transfer assuming all fin is at T = Tb) (Tx=L-Tf)/(Tb-Tf) 10. For an infinite fin, the temperature distribution is given by: (T-Tf)/(Tb-Tf)= e-mx. The heat flow through the fin is therefore given by: k (Tb-Tf)/L ● zero, because the fin is infinite ● infinite because the fin is infinite ● (Tb-Tf) (hP/k Ac)1/2 ● (Tb – Tf) (h P / k Ac)1/2 tanh (mL) 11. The Biot number, Bi, is defined as: • Bi=hk/L • Bi=hL/k • Bi= k/LH • Bi=qL/k • Bi=p UL/k 12. For a plate of length L, thickness, t, and width, W, subjected to convection on the two faces of area L x W. What is the correct length scale for use in the Biot number? . L ● W ● t • t/2 • L/2 13. If Bi…
Q3: Consider evaluation of different temperatures of solar photovoltaic/thermal system (PVT) as shown in Figure 1(a). The following set of differential equations represent energy balance equations to be solve using matrices and eigenvalues using MATLAB: dTglass = -0.75Tgtass + 0.75TpvT (1) dt - 1.187glass – 22Tpyr + 23Twax (2) dt dTwax 12Tglass + 18TpyT – 19 Twax (3) dt Where, Tgtass , TPVT, and Twax, are temperatures illustrated in Figure 1(b). At time t-0 the initial conditions are Tglass = 35 , Tpyr = 33, and Twax = 31 °C. Cold suppty In frem water Tank Glass PVT Espann Nane-PCMPVT Collector Wax Tubes Sterg Tank Nanofluid Heat Exchanger Contalner Tepe Teek oe Pump for drain
MATCH THE ANSWER WITH THE QUESTION Path Function Choose. Choose. Isobaric Process Pressure is constant Нeat Intensive property No work done Pressure Adiabatic Process Volume No transfer of heat
Wind power is defined as the use of air flow through wind turbines to provide the mechanical force to generate electricity. Wind power is an alternative to burning fossil fuels, and is renewable and produces no greenhouse gas emissions during operation. Modern horizontal-axis wind turbines often use three blades. Theoretically, the maximum power P (unit: watts) that a three-blade wind turbine can extract from the wind power can be calculated as: P = pAv³C₁. . (Equation 1) where p is the air density (kg/m³), A is the sweep area of the turbine (m²) and can be calculated from the length of the turbine blades, and v is the wind speed (m/s). Cp is the power coefficient that is unique to each turbine type. This coefficient represents the amount of kinetic energy from the wind that is captured by the turbine. From the Betz's limit law we know that the best power conversion possible is Cp,max = 0.59. Part 1 Given the following data: Blade length /= 50 m Air density p= 1.5 kg/m³ Power…
Your house has an electric water heater. Several friends are visiting you over the weekend and they are taking consecutive showers. Assume that at the maximum heating level, the heater uses 50 kW of electricity. The water use rate is a continuous 4 gallons per minute with the new water saving showerhead you recently installed. Your very old showerhead had used 7 gallons per minute. You replaced the showerhead because you learned that heating water was the second highest energy use in your home. By slowing the flow of water through the heater, the water temperature should increase to a higher temperature. (a) What is the change in temperature (T) for the old showerhead? (b) What is the change in temperature (T) for the new showerhead? Assume the system is at steady sate, and all of the 50 kW energy used is heating the water.