LIST P = 16F877A Using INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the microprocessor code that enables the fan to operate at 80% if the button on the 5th bit is pressed, and 30% if the button on the third bit is pressed

LIST P = 16F877A Using INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the microprocessor code that enables the fan to operate at 80% if the button on the 5th bit is pressed, and 30% if the button on the third bit is pressed

Name: LIST P = 16F877AUsing INCLUDE "P16F877A.INC" and PWM (Pulse Width Modu
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: LIST P = 16F877AUsing INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the microprocessor code that enables the fan to operate at 80% if the button on the 5th bit is pressed, and 30% if the button on the third bit is pressed.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter2: Introduction To Systems Architecture

Section: Chapter Questions

Problem 2VE: A(n) __________ is a storage location implemented in the CPU.

See similar textbooks

Similar questions

After scattering a 0.80 nm x-ray photon from a free electron, it bounces back at 1.4 x106 m / s. Write the C ++ code that finds the Compton shift in the wavelength of the photon. Write the C ++ code that finds the angle at which the photon scatters.
Use the following data declarations: .data byte Val word Val sbyte 1, 2, 3, FCh word 1000h, 2000h, 3000h, 4000h dwordVal dword 34567890h, 90785634h, 0Ah, 33445566h Show the value of the final destination operand after each of the following code fragments has executed: (If any instruction/s is invalid, indicate "INV" as the answer and briefly explain why) a. mov bh,byteVal+2 b. mov edx,1 C. add dx,[wordVal+4] mov ecx,5 xchg ecx,[dwordVal+12] d. mov ah, byte Val+3 sub ah,[ byte Val+0] sub ah,[ byte Val +2] e. mov eax, dword ptr dwordVal+7 f. movsx cx,byteVal+3 answer bh= answer edx= answer ecx= answer ah= answer eax= answer (show your answer in binary) CX=
Assignment for Computer Architecture! this is about hamming codes write the code IN MIPS ASSEMBLY LANGUAGE calculating hamming codes; The key to the Hamming Code is the use of extra parity bits to allow the identification of a single error. Create the code word as follows: Mark all bit positions that are powers of two as parity bits. (positions 1, 2, 4, 8, 16, 32, 64, etc.) All other bit positions are for the data to be encoded. (positions 3, 5, 6, 7, 9, 10, 11, 12, 13, 14, 15, 17, etc.) Each parity bit calculates the parity for some of the bits in the code word. The position of the parity bit determines the sequence of bits that it alternately checks and skips.Position 1: check 1 bit, skip 1 bit, check 1 bit, skip 1 bit, etc. (1,3,5,7,9,11,13,15,...)Position 2: check 2 bits, skip 2 bits, check 2 bits, skip 2 bits, etc. (2,3,6,7,10,11,14,15,...)Position 4: check 4 bits, skip 4 bits, check 4 bits, skip 4 bits, etc. (4,5,6,7,12,13,14,15,20,21,22,23,...)Position 8: check 8 bits,…
MIPS Assembly Write a program for RISC MIPS 32bits that challenges a person to guess a number of up to 3 digits before and 3 digits after the comma, that is, a value between 000,000 and 999,999. The program user will try to guess the number with multiple attempts, where the program will indicate at each attempt if the informed number is bigger, smaller, or if the user guessed correctly. When this happens, the program ends, showing a SUCCESS message and a total count of the number of attempts taken to get it right. The program must have a SUBROUTINE as described below. SUBROUTINE:- Input Parameters: user guess, expected value- Output: message on screen (bigger, smaller, SUCCESS)- Returns: value 1 if correct, 0 if incorrect
2.- If the binary code for LOAD is (0011), for ADD is (0010), for STORE is (0110), for JMP is (0001) and for END is (0111). Assuming a 16 bits format, write the object code (binary representation) of the following program: Note: use 4 bits for the op-code and 12 bits for the ADDR.
MOV AL, 5 ADD AL, 4 The flag register is affected by the above addition and the carry flag will equal * to 1 MOV AL,OF5H ADD AL,OBH After the addition AL will contain FF BB 00 11 IK
5. Load the register (CL) from the memory location [050OH] then subtract the content of this register from the accumulator (AL). Correct the result as a (BCD) numbers. Let [0500H] 12H & AL 3FH %3D
Convert below expression into three address code a := (c+d) * (c+b)
WAP program creates a BitArray of five Byte values (1,2,3,4,5) anddisplays each byte in its proper binary form:use c#
• In string operations, register -- - is used to point to the source operand and register ----- is used to point to the destination operand. The-----flag is used to tell the CPU whether to or -- - the pointer in string operation. Your answer
C++ Program: Make a program that would demonstrate the concept of Line Coding: Polar NRZ: Remember: if next bit is 1, there is inversion if next bit is 0, no inversion neg – means the signal is in the negative axis pos – means the signal is in the positive axis inv – means there is inversion no inv – means there is no inversion a. initially high (starts with positive, inverse is negative) Input: 1 1 1 0 0 1 0 1 1 0 0 0 Output: inv neg inv pos inv neg no inv neg no inv neg inv pos no inv pos inv neg inv pos no inv pos no inv pos no inv pos b. initially low (starts with negative, inverse is positive) Input: 1 1 1 0 0 1 0 1 1 0 0 0 Output: inv pos inv neg inv pos no inv pos no inv pos inv neg no inv neg inv pos inv neg no inv neg no inv neg no inv neg The logic here is when input is 1, next inputted 1 will be inverse…
Basic ARM assembly please, new to the language: Write an ARM assembly subroutine which, given the values of x and y in r0 and r1, respectively, calculates the expression: x3 + 6x2y + 12xy2 + 8y3, saving the result in r2. You don’t have to check for overflow (i.e. the solution and intermediate steps are okay to be bound to 32- bits). Hint: High-school algebra will make the solution much simpler.