n a plane stress condition, the components of stress at a point are sigma_{x}= 20MPa , sigma_{y} = 80MPa , Ty = 40 MPa . What is the maximum shear stress (in MPa) at the poin
Q: Problem 1 (6-1 , Eringen) Prove that in a nonlinear, isotropic, elastic solid the only possible…
A: given; prove that in a nonlinear ,isotropic , elastic solid the only possible initial stress is a…
Q: For a biaxial stress system consisting of fx=400 MPa(c), fy=175 MPa(t), fs=100 MPa, calculate…
A: To obtain the stresses at a plane which is 35 degree inclined to the x face, the given below…
Q: At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress…
A: Given:σx=-30 MPaσy=15 MPaζxy=25 MPaθ=-25°
Q: Rod AB is fixed at side A with a length of 500m and a diameter of 20m. On side B, the rod…
A:
Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 144 lbs…
A:
Q: 2. Assume the plane stress state: ơ1 = 50, 02 = -250, T12 = 150 (all stresses in MPa). 2.1. Sketch…
A: σ1=50MPa σ2=-250MPa τ12=150MPa To Find Mohr's Circle Principal stress and their direction Maximum…
Q: e state of stress at a point in a circular bar under pure torsion is given by T xy = T yx= t and…
A:
Q: A state of stress is specified in the figure shown below. Determine the Normal stress ox (mPa) on…
A:
Q: Determine the equivalent state of stress on an element at the same point oriented 60 degrees…
A:
Q: 2. Using maximum shear stress theory (MSS) the factor of safety for ductile material with Sy=220…
A:
Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…
A:
Q: The state of stress at a point is Ox=-10 kpsi, oy=10 kpsi, az=-20 kpsi, Txv=D5 kpsi, Tyz= 2 kpsi,…
A:
Q: (i) What is the difference between Mohr-Coulomb failure criterion and Tresca failure criterion?…
A: (ii) Given: The stress along x-direction = -35 Kpa The stress along y-direction = -65 Kpa The shear…
Q: If o = 50 ksi, Oy = 10 ksi, and Txy = 30 ksi, what is the absolute maximum shear stress for the…
A:
Q: At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress…
A: Given:σx=-30 MPaσy=15 MPaζxy=25 MPa
Q: What is the maximum shear stress RESULTING FROM THE COMBINATION OF THE FOLLOWING stresses: Tesile…
A: Given data: Sx=200 MPaSy=100 MPaSS=50 MPa Need to determine the maximum shear stress.
Q: I Review Determine the normal stress developed at corner A of the column. Take P = 280 kN and P, =…
A:
Q: The internal loadings at a cross section through the 130-mm-diameter drive shaft of a turbine…
A:
Q: The principal stresses at a point in a critica section of a machine component are o, = 60 MPa a, =5…
A: Given:σ1=60 MPaσ2=5 MPaσ3=-40 MPaσy=200 MPa
Q: At a point in a material under stress, the intensity of the resultant stress on a certain plane is…
A: Draw the Mohr circle indicating the resultant stress on the plane. Write the expression for the…
Q: 7 Principal stresses of a point in a critical section of a machine component are: ₁= 80 MPa 0₂= 5…
A:
Q: QITHE state of plane stress at a point is represented by the stress element below: A. Draw the…
A:
Q: The principal strains in a plane, measured experimentally at a point on the aluminum fuselage of a…
A: Write down the given value using suitable variables. Here ε1 and ε2 signify principal plane…
Q: 2. The state of stress at a point in a machine part is given by the following stress tensor. The…
A:
Q: Sx = 3600 psi, Sy = 1400 psi, Sxy = 2500 psi B = 48° The magnitude of the normal stress? The…
A: Given Data: Stress in the x-axis, Sx=-3600 Psi Stress in the y-axis, Sy=1400 Psi
Q: Part 1 A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the…
A: Part 1As per given dataPx=Fx=-20kNPy=Fy=-16kNPz=Fz=-11kNPart 2Mx=16510-11230Mx=5630 kN.mmMx=5.63…
Q: 26. If ơ, = 50 ksi, oy = 10 ksi, and Txy = 30 ksi, what is the absolute maximum shear stress for the…
A: Given: The stress along x-axis, σx = 50 ksi The stress along y-axis, σy = 10 ksi The shear stress,…
Q: 4. Shown below is a steel tube AB with a 1.5" outside diameter and .06" wall thickness. You may…
A: Given:do=1.5 int=0.6 indi=0.9 inF=50 lb
Q: A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected…
A:
Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…
A: given; Sx=150MPa (tensile)Sy=-21MPa (compressive)Sxy=85MPaβ=560
Q: The state of plane-stress at a point is given by σx = -200 MPa, σy = 100 MPa and txy = 100 MPa The…
A: Data given- σx = -200 MPa, σy = 100 MPa txy = 100 MPa
Q: ssume oz = 500, oy = 300, Tzy = 250, Oyicld = 350. Answer the following questions. Click here for…
A: Given Data⇒ σx=500 MPaσy=300 MPaζxy=250 MPa
Q: Derive the following equation for computing shear stress in a solid bar along an oblique plane with…
A:
Q: Problem 9.51 In (Figure 1), Tzy = 55.3 MPa. Figure 80 MPa 1 of 1 > Part A Determine the principal…
A:
Q: GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane…
A:
Q: Choose the stress to which the size correction factor should be applied in Soderberg's formula. a.…
A: Choose the stress to which the size correction factor should be applied in Soderberg's formula.
Q: If principle stress opi = 100 N/mm (tensile) op2 = 40 N/mm (compressive), then maximum shear stress…
A: Given, Maximum principal stress = σp1 = 100 N/mm2 (Tensile) = 100 N/mm2 Minimum principal stress =…
Q: If o, = 30 ksi, o, = 10 ksi, and Txy = 20 ksi, what is the maximum normal stress, in ksi, for the…
A:
Q: Choose correct answer: Maximum stress on a principle plane is Tangential stress shear stress…
A: Option C is correct normal stress
Q: 2: ural stress which fluctua MN/m2 and - 115 MN/
A: Givenflexural stress σ1=250MN/m2σ2=-115MN/m2yield strength σy=0.55σultEndurance strength…
Q: A rod of square 30x 30mm^2 cross-section subject to a compressive axial force of 72kN and a twisting…
A:
Q: 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given…
A:
Q: hear stress element. Any stress components not shown are assumed to be zero. Work problem #4
A: Part A) First, draw the coordinate system and depict the given point in the below expression.
Q: Determine the equivalent state of stress on an element at the same point onented 30°…
A:
In a plane stress condition, the components of stress at a point are sigma_{x}= 20MPa , sigma_{y} = 80MPa , Ty = 40 MPa .
What is the maximum shear stress (in MPa) at the point?
Step by step
Solved in 2 steps
- During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
- An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clementThe stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
- Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.The strains for an element of material in plane strain (see figure) are as follows: x = 480 ×10-6. y = 140 × l0-6, and xy = —350 x 10”. Determine the principals strains and maximum shear strains, and show these strains on sketches of properly oriented elements.An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
- The normal and shear stresses acting on element A are 6500 psi, 17,300 psi, and 2900 psi (see the figure b for Problem 7.2-5). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?