Open Circuit Simulator App, Click on circuits tab on the top and select Blank circuit. Draw the below given circuit. Change the value of components according to your circuit. Use ammeter, voltmeter and ohmmeter to measure the current, voltage and resistance. Find the current flowing through the 10 Ohm resistor directly by simulation and verify the same using Norton's theorem. 4Ω 10 ww- 16 2 10 2 12 V ww ww ww

Open Circuit Simulator App, Click on circuits tab on the top and select Blank circuit. Draw the below given circuit. Change the value of components according to your circuit. Use ammeter, voltmeter and ohmmeter to measure the current, voltage and resistance. Find the current flowing through the 10 Ohm resistor directly by simulation and verify the same using Norton's theorem. 4Ω 10 ww- 16 2 10 2 12 V ww ww ww

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Three 47.1 ohm resistors and three 17.1 H inductors are all in series with a 37 volt battery and a switch. The switch is placed in position A at time t = 0 and switched to position B at time t = 743 ms. Find the voltage across each of the resistors at time t = 1.17 seconds. Owo DO A R R in in ete SW éte لفظو
Write down Kirchoff's loop and junction equations which can be used to analyze the circuit shown. Draw arrows on the circuit that indicate the direction for the current in each branch. 252 15V my 12V The current through the 2 ohm resistor is 4.0 A going from left to right. Find the current in the other branches of the circuit. What is the voltage drop across the 4 ohm resistor? What is the voltage drop across the 3 ohm resistor?
INSTRUCTIONS: Solve the following problems. Show and COMPLETE solutions. Draw all CIRCUIT DIAGRAMS or the equivalent circuit (dummy circuit) as the case may be. Write your solutions on sheet/s of short bond paper. A battery is to consist of 20 identical cells. The emf of each cell is 1.5 V and the internal resistance is 0.20 ohm. This battery will be used to supply power to a 10 ohm lamp. Determine the current on the lamp if:1. The 20 cells are connected in series 2. The 20 cells are connected in parallel 3. The 20 cells are arranged 5 cells in series in 4 parallel rows.
Define a linear circuit. Find the current Io in Figure 1 using source conversion technique.
Finally, the multimeter is used to measure VOUT_C for the third potential divider. The circuit values are: VIN = 3.5 V, R1 = R2 = 6.6 kQ2, R3 = R4 = 660 kQ, and R5 = R6 = 6.6 MQ. VIN www www.ta R5 R6 VOUT C 1M Multimeter Your multimeter shows the measured value for VOUT_C to be 0.44 V. Consider the 3 resistors in the schematic above and recalculate what you expect the measured VOUT_C to be.
2. Determine the voltage with respect to ground at each point in below. Assume the practical model. Solve and Simulate to compare the result. D1 D2 C R A B D 1.0 kΩ + Vs2 8 V VsI 25 V
A circuit has two batteries and four resistors, connected as shown below. www 592 5 V 392 292 I 192 3 V 1. Find the total effective resistance in the circuit. 2. Write a junction rule for each possible junction in the circuit. Be as specific as you can, but you don't need to solve for anything. 3. Write a loop rule for each possible loop in the circuit. Be as specific as you can, but you don't need to solve for anything.
My question is the Ri does mean the resistance inside the voltage source or just an addition resestor that out side just to resist the voltage ??
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
Voltage sources in series Select one: a. When two or more voltage sources are connected in parallel, the total voltage equals to the sum of all individual voltage sources b. When two or more current sources are connected in parallel, the total current equals to the sum of all individual current sources C. When two or more current sources are connected in series, the total voltage equals to the sum of all individual voltage sources d. None of the answers e. When two or more voltage sources are connected in series, the total voltage equals to the sum of all individual voltage sources OO Shot by Hisense H12
subject:Circuits 1please this one too give me a slightly favor can you answer this questions please wanna learn more im having difficuilty about this questions
Determine the total resistance, Rī, and current, I, for the circuit in Figure Q1(b). 30V- RT 50Ω 2002 4092 7092 m Figure Q1(b) 3002 m 6092 [Answer: 22.430, 1.34A]