p = 4.5 m

Q: Example 1.10 gave an analysis that predicted that theviscous moment on a rotating disk M = πμ V R 4 ...

A: The expression of the viscous moment for a rotating disk, The uncertainty of each variable is given...

Q: Prove that a refrigerator’s COP cannot exceed that of a completely reversible refrigerator that shar...

A: Two refrigerators of reversible and irreversible are shown in below figure Assume coefficient of per...

Q: Determine the resultant R of the system of distributed loads and locate its line of action with resp...

A: Divide total load in two uniform varying loads (A-O) and (O-B) Total load due to UVL (A-O) is area o...

Q: Two aligned parallel rectangles with dimensions 6 m * 8 m are spaced apart by a distance of 2 m. If ...

A:

Q: Hot air at atmospheric pressure and 80°C enters an 8-m-long uninsulated square duct of cross section...

A: Given data To determine  Exit temperature of air T2..?? Rate of heat loss from duct to the attic sp...

Q: A mass of 1 slug is attached to a spring whose constant is 25 /4 lb /ft. Initially the mass is relea...

A: Consider m as the attached mass, k as the spring constant, and β as the damping coefficient. Write t...

Q: Q3.The force F - 5001b acts on the frame. Resolve this force into component acting along members AB ...

A: Given data Load acting at point A is 500 lb To determine the forces acting along the members AB nd ...

Q: Can you please do P7.41   Thx

A: The loading diagram of the beam is shown as follows, Let's draw the free body diagram of the beam,

Q: Conservative forces lose no mechanical energy to.

A: Conservative forces are those forces ,which if act, there is no loss of mechanical energy of a syste...

Q: (C) A plain sided specimen is subjected to 2 * 107 cycles at the applied stress range of 100 MPa. Es...

A:

Q: What is Material Property Relationships?

A: The material property relationships are those relations that interact with the properties of materia...

Q: Q2: Replace the three forces acting on the gear by an equivalent system consisting of a force at O a...

A: Consider a force of magnitude 1.2 kN is acting on the location where the force 2.4 kN is acting. If ...

Q: 13-37. If the 75-kg man stands in the position shown, determine the state of stress at point A on th...

A:

Q: El siguiente tubo que se muestra a continuación tiene un radio exterior de 50 mm y un radio interior...

A:

Q: Convert between energy units. 2.85x10^3 J to cal

A: Understand that the joule is the SI unit of energy and Calorie is used as the unit of energy in the ...

Q: The box is at rest at point 1 when it is sliding down the incline. If the 1 1 H, = 0.40 HA = 0.30 %3...

A: Let mass of box be M After beginning of motion kinetic friction comes into action So from 1 to 2 FBD...

Q: Complete the table. a. 355 km/s cm/s m/ms b. 1228 g/L g/mL kg/ML c. 554 mK/s K/s uK/ms d. 2.554 mg/m...

A: A. 355 km/s into cm/s: Thus,

Q: Q1 In three members having one as zero force member in truss, what if ?there is an external force ap...

A: In three members having one zero force member is possible only if there is no load or force on joint...

Q: Two bars, a pulley, and a cable are used to sup- The two bars have port a block as shown in Fig. neg...

A: Given data To determine  Internal force at cross section a-a of the bar AB..??  

Q: In a game of pool, ball A is moving with a velocity v0 with a magnitude of v0 = 15 ft/s when it stri...

A: To proceed with the problem some assumptions need to be taken into consideration. Mass of each ball...

Q: A 900-mm rod rests on a horizontal table. A force P applied as shown produces the following accelera...

A: The free body diagram which explains how the system works  

Q: FR 24. Determine the resultant moment produced by the forces about point 0 GM.F.d

A: Let's first resolve the forces F1 and F2 into horizontal and vertical components.

Q: The collar is released from rest in the position shown and slides down the fixed rod. Calculate (a) ...

A:

Q: A venturi meter has water flowing through it. The pressure difference is 1 psi. The diameter at poin...

A:

Q: Mechanical Engineering Question

A: Let's first determine the tension by writing the coordinates of A, B, and C. The coordinates of A, B...

Q: A 195-lbm astronaut took his bathroom scale (a spring scale) and a beam scale (compares masses) to t...

A: Given data Mass of the austronut m = 195 lb Acceleration due to gravity g =5.48 ft / s2 To determine...

Q: Estimate the critical stress of the surface flaw in a ceramic whose Young's modulus and surface ener...

A:

Q: Discuss the stability of (a) a submerged and (b) a floating body whose center of gravity is above th...

A: The submerged body is a body that is lying fully in water. If the center of gravity of submerged bod...

Q: The given truss below is loaded vertically downward with 4KN and 8KN at points C and D, respectively...

A:

Q: A solid circular rod of diameter d undergoes a bending moment M = 113 Nm inducing a stress σ = 16M/ ...

A: Given: Given: The bending moment on rod, M = 113 N.m The strength of the rod, S = 172.4 MN/mm2 The f...

Q: Define the term absolute maximum shear stress in the material?

A: Let us understand the term Absolute maximum shear stress by help of Mohr's circle.  

Q: Determine the maximum allowable intensity w of the uniform distributed load that can be applied to t...

A: Given : Allowable bending stress = 165 MPa Solution :  

Q: The thin-walled cylinder can be supported in one of two ways as shown. Determine the state of stress...

A: Given data as per the question Internal pressure = 65 psi Wall thickness = 0.25 in Diameter = 8 in r...

Q: The collar is released from rest in the position shown and slides down the fixed rod. Calculate (a) ...

A: Write the given data:  

Q: Determine the bar force in members f9; hi ; 9d 4 bc 2o00

A: Draw the F.B.D for the given truss. For the equilibrium of the truss. Negative sign indicates the ...

Q: Explain how the LMTD method can be used to determine the heat transfer surface area of a multipass s...

A: Cross Flow heat exchanger: In this type of heat exchanger  hot and cold fluid travel in perpendicula...

Q: Show that the incompressible velocity potential in plane polar coordinates o(r, 0) is such that аф 1...

A: Velocity potential function is defined as a scalar function of space and time such that its negative...

Q: Consider a recuperative cross-flow heat exchanger (both fluids unmixed) used in a gas turbine system...

A: The mass flow rate of the exhaust gases, mg = 7.5 kg/s The inlet temperature of the exhaust gases, T...

Q: Q5:The wrench is subjected to the 200 N force and the force P. If the equivalent of the two forces i...

A:

Q: What is the forklift trucks system?

A: Forklift trucks are the industrial vehicles used for transportation of cargo from one point to anoth...

Q: An ideal Diesel cycle with air as the working fluid has a compression ratio of 18 and a cutoff ratio...

A:   The compression ratio of the cycle is: r=18 The cut of the ratio is: rc=2 The pressure at stage 1...

Q: For number, underline the zeroes that are significant and draw an x through the zeroes that are not....

A: The rules of significant figures are given as, (1) All non-zero digits are taken as significant. (2)...

Q: 9-6* Two blocks with masses mA = 50 kg and mg = 100 kg are connected with a flexible cable that pass...

A: The free body diagram of block A is given as, On using the force equilibrium in direction of perpen...

Q: 6-50 The mass of the cylinder shown in Fig. 100 kg. Determine the reactions at contact points A and ...

A: Given data as per the question Mass = 100 kg  Force = 300 N considering the free body diagram of the...

Q: Draw complete free-body diagrams for the bodies specified in the following problems. Neglect the wei...

A: Draw the free body diagram of the bar AC.

Q: The rear wheels of the car in the figure is kept locked by the brakes whiles the front wheels are fr...

A: 1) As given in question rear wheels are locked and front are free to turn so we can consider front w...

Q: A heat source at 800 K loses 2000 kJ of heat to a sink at (a) 500 K and (b) 750 K. Determine which h...

A: Entropy is associated with irreversibility of a system, it is the degree of disorderness or randomne...

Q: Determine the energy lost due to friction and the impacts for Prob. 14.1.Reference to Problem 14.1:

A: The mass of the bullet is written as, The initial velocity of the bullet is given as, The mass of ...

Q: A single-pass cross-flow heat exchanger uses hot air (mixed) to heat water (unmixed), flowing with a...

A: Write the given data.

Q: P2-5. Show how to resolve each force into its x, y, z components. Set up the calculation used to fin...

A: Given data *The given force, F = 800 N

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.