P C 3m 3 1 2 4m

Q: Use the graphical method in solving the bar forces D 12 m B E 1200 kN 12 m F 9m 2400 KN 1200 kN

A:

Q: Determine the vertical displacement at point B if El is 15.0 x 10^3 kNm^2 Note: Use two (2) decimal…

A:

Q: 2.15 Determine the moment M, at the base of the but- tress due to the applied thrust force F. Use…

A: To find the Moment about A-

Q: 3. Determine the vertical displacement of joint D. Given AE consta D 3 m 4 m 4 m 15 kN 20 kN

A: Data given: Asked: Vertical displacement of joint D

Q: C. Three cylinders are piled in a rectangular ditch as shown. R, = 5cm, R2 = 6 cm, R3 = 5 cm. W, =…

A: Reactions at A, B and C are :

Q: The dam shown has a base of which 2 m. below the ground surface. The pressure distribution diagram…

A: Given:- To find:- Uplift force per unit length = ?

Q: 1. A uniform crate of mass 30 kg must be moved up along the 15° incline without tipping. Knowing…

A: Solm ⇒            m=30 kg* when the crate is about to tip , Normal    force N will be zeero.Now zMc…

Q: in the crest gate on a dam shown in the figure,: surface AB form's the arc of a circle.of 6. m.…

A: To determine the vertical component of total pressure on the curved gate AB.   Given, Radius of the…

Q: H.W The uniform thin pole has a weight of 50 N and a length of 26m. If it is placed against the…

A:

Q: Set P1_1 = 58 kN , P2_2 = 33 kN . (Figure 1)

A:

Q: 2в0 KN-m 9m B 4m R=500 KN

A:

Q: termine the reactions at support and thne forces acting on each member. By applying 1 uni oad…

A: In addition to its initial horizontal speed, a projectile's horizontal displacement depends on its…

Q: W.S. 1.30 m W.S. B (hinge) Figure 4a 3.00 m -2.00 m-

A:

Q: 10KN/m 5KNM A B 5m

A: to calculate slope at free end.

Q: Determine the horizontal displacement of Point B by using the reduction theorem. Take El 1000 kN.m.…

A: EI is constant

Q: up B What is the total resultant force (kN) that is applied on surface AB? Then find the location of…

A:

Q: calculate the vertical deflection at point B (using work-energy method). Assume M1=50 kNm and M2=70…

A:

Q: 1. From the figure, determine a. Rx b. Ry c. Magnitude of Resultant d. The inclination of the…

A:

Q: 8. The pressure coefficient at a stagnation point is a) +1 b) -1 c) 0 d) Infinite

A: The pressure coefficient at a stagnation point is +1 it is dimensionless number.  it describes the…

Q: If the moment of forces at B= 15 KN.m counterclockwise, and w= 25 kN, Find T? 36 m

A:

Q: Consider the beam shown below: A L If P = 7.5 kN and L = 1.8 m, the horizontal displacement at A (in…

A: Note - since one end is fixed, so horizontal displacement will be zero.

Q: Determine the vertical displacement at point B. 15 kN 6 kN/m 2EI COO El El VA 2.0 m 4.0 m 2.0 m Vo…

A:

Q: A simply supported beam carries a concentrated load of 31 kN at 7 meters from the left support (1…

A:

Q: 2. Determine the slope at C and the displacement at B El is constant. Use Moment area theorems. 10…

A: Given a cantilever beam with point load and we have to find slope at c and deflection at B

Q: Determine the vertical displacement of point C. El is constant. Use the method of virtual work. 80…

A:

Q: Determine the vertical displacement of Point EI is Constant. 10 KN C. 6 kN/m A & 3m к Use E = 2E8…

A: Moment of inertia being a function of two variables viz. width and depth. The values of these can be…

Q: Dam ABC is made of concrete 22 kN/m³. Determine the hydrostatic force and its moment about point C.…

A: Draw the free-body diagram of the dam. The unit weight of the concrete is γc=22 kN/m3. The unit…

Q: 4. Block B weighs 200N and block C weighs 100N. See Figure4. Determine the weight of block D and the…

A: ASKED: To determine the weight of block D and angle θ for equilibrium.   Given, Weight of block B =…

Q: EXERCISE 3.2: A pin-jointed plane truss is pinned at point A and supported on a roller at point E.…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: 2. With the increase in pressure, the exit velocity a) Decreases b) Increases C) Same d) Independent

A: This question is related to the Fluid Mechanics.

Q: 1. Determine the slope at D 2. Determine the deflection at D P=800 kN 4 kN a=3m B- 3 m 3 m

A: Solution;

Q: Determine the deflection at point C using double integration method. EI=constant, w=30 kN/m a=3m and…

A: A cantilever beam is given, we need to find out Deflection at point C using Double Integration…

Q: Analyze the given structure below. Calculate for the slope at the free end (Use: DOUBLE INTEGRATION…

A:

Q: 8.5 and 8.6 the mc to supp for Ou and th 250 kN 250 kN 250 kN B D E 0.9 m 0.9 m 0.9 m 0.9 m Fig.…

A:

Q: Determine the Resultant Force, its magnitude and direction of the given co-planar, concurrent forces…

A:

Q: 2. At what angle 0 must the 800 lb force be applied in order that the resultant R of the two forces…

A:

Q: B. A rectangular scow having a length of 15 m, width of 8 m, and 6 m deep has a displacement of 164…

A:

Q: 9.5 Refer to Figure 9.14. Given: L = 4 m; for sand, y = 16 kN/m2: ø' = 35°; and, for clay, Yat =…

A: Question is based on cantilever sheet pile wall penetrating a granular value. Length , unit weight…

Q: Calculate the horizontal displacement of point B. El is constant for all members 120 kn/m 100 kn В C…

A:

Q: a. Determine the vertical displacement at joint B b. Determine the horizontal displacement at joint…

A:

Q: A barrel in the form of a frustum of a cone with a radius of 3m at the top and 6m at the bottom. It…

A: Hydrostatics, is a part of liquid mechanics that examines the condition of equilibrium of a drifting…

Q: 3. The circular shaft is supported by two journal bearings at A/C and B. internal shear force V(x)…

A:

Q: 0. Vertical Forces P & F in the figure produces a resultant of 500KN and a counter clockwise couple…

A:

Q: A 35-kg disk rests on an inclined surface for which μs = 0.2. Determine the maximum vertical force P…

A: Consider the following free body diagram of the disk :

Q: PROBLEM 2: The 200 kN block shown has impending motion up the plane caused by the horizontal force…

A: To find coefficient of static friction

Q: 50 KN 2m C. The force R = 600 kN is the resultant of the forces P, Q and 50 kN in figure 3. 1.…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: 1. The forces acting on a 1-ft length of a dam are shown. The upward ground reaction varies…

A:

Q: The small collar of mass m = 0.62 kg is released from rest at A and slides down the curved rod in…

A:

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.