Plz give the correct answer. Compute the intensities of active and passive earth pressure at depth of 8 m in dry cohesionless sand with an angle of internal friction of 30 degrees , and unit weight of 18kN / (m ^ 3) What will be the intensities of active and passive pressure if the water level rises to the level? Take the saturated unit weight of sand as 22kN / (m ^ 3)

Plz give the correct answer. Compute the intensities of active and passive earth pressure at depth of 8 m in dry cohesionless sand with an angle of internal friction of 30 degrees , and unit weight of 18kN / (m ^ 3) What will be the intensities of active and passive pressure if the water level rises to the level? Take the saturated unit weight of sand as 22kN / (m ^ 3)

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.8P

See similar textbooks

Similar questions

Solve the following problems. Provide complete solutions and summary of answers. The water table in soil deposit is 2 meters below the ground surface. The soil above the water table has a dry unit weight of 14.85 kN/cu. Meter. The saturated unit weight of the soil is 20.58 kN/cu.meter. Determine the following: a. Total Stress at a point 4.80 meters below the ground b. Total Pore pressure 4.80 meters below the ground c. Total effective stress at a point 4.80 meters below the ground.
1.A dry sand is known to have an angle of internal friction of 29. A triaxial test is planned, where the confining pressure will be 41 kPa. What is the maximum axial stress, in kPa, (major principal stress) that can be applied? Calculate the value to 1 decimal place. Do not provide units in your answer. 2.A clay soil is subjected to a triaxial test under unconsolidated-undrained conditions. At failure, the major and minor principal stresses are 8401 psf and 4875 psf, respectively. What is the shear strength of this soil if the confining pressure is doubled? Provide your answer in psf with no decimals.
The sub-surface profile at a certain site is shown in Figure. Given that YSM =112pcf, YML =109pcf, /ML,sat =113pcf, lateral earth pressure coefficient at rest K₁ =0.54. Compute U, Ox, Oz, Ox', andoz at Point A. Solution: Total vertical stress at A: O₂ = • Pore water pressure at A: u = • Effective vertical stress at A: 0₂ ● Effective horizontal stress at A: Ox' Total horizontal stress at A: Ox II psf; psf; psf; psf; psf; Silty Sand: (SM). Clayey Silt (ML) ▼ 12 ft 10 ft 11 ft
The ground conditions at a site are shown in the figure below GL Sand Water table is at ground level = 20% 5 m %3D Water content Specific gravity of solids = 2.7 Unit weight of water = 10kN/m a) The saturated unit weight of the sand (kN/m³) is (a) 15 (b) 18 (c) 21 (d) 24 B) The total stress, pore water pressure and effective stress (kN/m2) at the point P (a) 75, 50 and 25 (b) 90, 50 and 40 (c) 105, 50 and 55 (d) 120, 50 and 70 a0081
. A soil profile is shown in figure below. Dry sand Yay- 165 KNm 6m Groundwater table Saturated sand 13m Yu 19.25 kN/m" Dry sand Saturated sand Clay Calculate the following: a. Effective stress at point A in kPa. b. Effective stress at point B in kPa. c. Effective stress at point C in kPa.
A soil profile is shown in figure below. Dry sand 6m Ydry = 16.5 kN/m³ B Groundwater table Saturated sand 13m Ysat = 19.25 kN/m² C Dry sand Saturated sand Clay Calculate the following: a. Effective stress at point A in kPa. b. Effective stress at point B in kPa. c. Effective stress at point C in kPa. 5.
There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the bottom the sample, if the saturated unit weight of the sample, is 18.9 kN/m3. Provide Diagram a.709.5 b.177.38 c.88.69 d.354.75
12. A glass container with previous bottom containing fine sand in loose state, with void ratio of 0.08, is subjected to hydrostatic pressure from underneath until quick condition occurs in the sand. Specific Gravity of sand particles = 2.65 Area of cross-section of sand sample = 12 cm2 Height of sample = 10cm Compute the critical gradient of the sand under quick sand condition. Compute the head of water to cause quicksand condition. Compute the seepage force acting from below.
Question 1: (10) For the soil profile shown below where H1 = 5 m and H2 = 5 m: a) Calculate the total stress (o), pore water pressure (u), and effective stress (o') at point A. b) In order to decrease the effective stress at point A by 15 kN/m2, what would be the depth of the water table from the ground surface. XXXX H1 Dry Sand e = 0.60 G, = 2.68 Clay H2 e 0.80 G = 2.75 %3D %23
Dry Sand H Groundwater Table Clay H, Refer to the soil profile shown. Given H1 = 9.46 m., and H2 = 4.79 m. If the ground water table rises by 2.58 meters, determine the change in effective stress (numerical value only, in kPa) at the bottom of the clay layer. Properties of dry sand: Gs = 2.57, e = 0.63. Properties of clay: Gs = 2.74, e = 0.88. Round off to two decimal places.
For the soil profile shown below, the piezometer reading is 1 m above the W.T level calculate the total and effective stress (vertical and horizontal) at points A and B. Use ko = 0.5 N.G.L W. T I m Piezometer 5 m A y = 15.9 kN/m³ Clay Ysat = 14.4 kN/m³ B Sand under artesian pressure 0.45 m 7.55 m 7.55 m
Question 33 Dry Sand H, Groundwater Table Clay H, Refer to the soil profile shown. Given H1 = 9.89 m., and H2 = 5.8 m. If the ground water table rises by 3.78 meters, determine the change in effective stress (numerical value only, in kPa) at the bottom of the clay layer. Properties of dry sand: Gs = 2.53, e = 0.63. Properties of clay: Gs = 2.75, e = 0.81. Round off to two decimal places.