Power factor 90 to 100% 88 to <90% 85 to <88% 80 to <85% 75 to < 80% 70 to < 75% 65 to < 70% 60 to < 65% 55 to <60% 50 to <55% Less than 50% Surcharge None 2% 4% 9% 16% 24% 34% 44% 57% 72% 80% Use the table given for the following. a. What is the effective impedance? What is the average current drawn? What will be the surcharge? b. c. If a house with inductive loads has an avg consumption of 40kW and 26kVAR is supplied 230 Vrms source.

Power factor 90 to 100% 88 to <90% 85 to <88% 80 to <85% 75 to < 80% 70 to < 75% 65 to < 70% 60 to < 65% 55 to <60% 50 to <55% Less than 50% Surcharge None 2% 4% 9% 16% 24% 34% 44% 57% 72% 80% Use the table given for the following. a. What is the effective impedance? What is the average current drawn? What will be the surcharge? b. c. If a house with inductive loads has an avg consumption of 40kW and 26kVAR is supplied 230 Vrms source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

For Fixed Bias Configuration Solve for Ib, Ic and le. Atleast 2 decimal place. Be mindful of units. Assume Ic is not equal to le. ... 4 RC 15002 RB VCC 20V 90A/A 100k2 Ib=Blank 1 HA Ic=Blank 2mA le=Blank 3 mA Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer
Draw the circuit diagram of Two quadrant chopper which is having average load voltage might be positive or negative. Explain each quadrant operation with neat sketch. I want more than 350 words and I do not want it in handwriting
Damping ratio quettion.
ssignment_2 5 Immersive Reader O Open in Deskt (b) Connected in paralld. 7) The following readings are obtained in the measurement of an inductor: 1.003,0.998, 1.001, 0.991, 1.009, 0.986, 1.005,0.997, 1.008, and 0.994 µH. Determine the (a) Arithmetic mean. (b) Average deviation. (c) Standard deviation.
aloulated m O1 the value you Up = A cos wt +1o Calaulate maarli)-min(i) =? Use constant voltage drop mad. Don7 to write units. . - 3.7V forget
Q. Define m00 re riachiné.. MOo DAw the State diagream of 1011 wi thout overlaPping
These question from electronics two course
Determine the following for the fixed- biased configuration. (Use 4 decimal places) a. IBQ and ICQ b. VCEQ c. VB , VC and VBC
e+ VBB = 12Y. 50k VE RBB- 5Kd 7= 0.6 ATEM F 50052 Ip= 1OUA. GND DETERMINE: A) RB1 B) RB2 C) Vp D) VR2, DURING THE CHARGING PHASE E) VR2, DURING THE DISCHARGING PHASE.
1) The term Bi is defined as Select one: O a. Negative change in reference bus power to the power change DPi on bus i O b. All of these 1/Pfi Clear my choice
circuits 48 49
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?