Answered: Problem 2-5: The rectangular plate is…

Problem 2-5: The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear strain Yxy in the plate. A 150 mm B 3 mm 200 mm T 3 mm x

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.3P: An element of material in plain strain is subjected to shear strain xy = 0.0003. (a) Determine the...

See similar textbooks

Related questions

Q: A single-stage axial flow pump with outer radius r2 =0.240 m and inner radius r1=0.120 m is given.…

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 125 KN,…

A: Given : The shear force in this section is The diagram is,

Q: vertical distance from the location where the maximum shear stress occurs

Q: Consider a modified cogeneration power plant with regeneration. Steam enters the turbine at 6MPa and…

A: Steam enters the turbine at P=6 MPa and T= 450 oCTotal mass of steam entering to the turbine The…

Q: Problem 1-81: Determine the required diameter of the pins at A and B if the allowable shear stress…

A: τallow =100 MPa

Q: 25/A- Airbus 320 fly in steady level flight with altitude 10.5 km and the density at this level…

Q: A spur pinion with No = 47 teeth runs at n₁ = 188 rev/min пр and has a diametral pitch, P of 10…

Q: This is a graph that plots the velocity of an object against time. (a) What is the average…

A: graph Velocity (V) vs time (t)

Q: Write down the homogeneous transformations AT & T for the frames shown in Fig.2

A: Given:To find:Transformation matrix .

Q: Q4) An aluminium pan whose thermal conductivity is 237 W/m - °C has a flat bottom with diameter 20…

Q: 1) Water (p= 1000 kg/m³, u=0.001 Pa-s) flows trough a horizontal asphalted cast iron pipe 20 cm in…

Q: Consider a two-dimensional flow which varies in time and is defined by the velocity field, u = 1 and…

A: The objective of the question is to determine whether the given two-dimensional flow field is…

Q: 3.3 Evaluate the specific physical exergy, ePH, in kJ/kg, of a stream of (a) saturated water vapor…

Q: Q2/ The sensible heat of 500 kW is required to be added to the saturated air at 10 °C dry-bulb…

A: The sensible haetAnd air is saturated at 10 degree dry bulb temperature.Volume flow rateFrom the…

Q: 2. You are working for a glider manufacturer and have been asked to analyse the laminar boundary…

A: For the solution refer below images.

Q: as the thin square plate hangs at rest from pin A, a bullet of a mass of 40.0 g is fired…

A: The mass of the bulletInitial velocity of the bullet

Q: 3- A forced circulation boiler delivering 36 kg/s at 130 bar is operated with a circulation ratio of…

Q: 1- Two mass-spring-damper systems A & B. System A has = 0.1 and wn = 20 rad/sec, and system B has =…

A: Here we will apply the damping coefficient comparison

Q: A tank in the shape of a half-cylinder lies on its side as shown in the picture below. The units…

Q: 1. Steam expands in an adiabatic turbine from 8 MPa and 500°C to 0.1 MPa at a rate of 3 kg/s. If…

Q: a₁ W Figure 37.1 A propeller of an axial flow pump U₁ Outlet guide vane B₁ Impeller A₂ B U₂=U₂=U V12

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 125 KN,…

Q: Bar AB has an angular velocity AB = 7 rad/s Part A Determine the velocity of the sider block Cat the…

A: Given:BC = 350 mmAB = 500 mm or 0.5 m/s90° - 60° = 30°45°7 rad/sRequired:VC ( velocity of slider…

Q: The last blade row of a turbine has a relative outlet flow angle of 70 degrees. if the relative…

Q: Let F₁ = [F1] Ib. Find the resultant R of the two forces. a) Determine the magnitude R of the…

A: Find outDetermine the magnitude of the resultant force.Determine the direction of the resultant,…

Q: 1.31 A tank of oil has a mass of 25 slugs. (a) Determine its weight in pounds and in newtons at the…

A: Given data:-The mass of the oil Determine:-a) Its weight in pounds and in newtons at the earth's…

Q: The vertical U-Section of a water distribution system seen on the drawing is considered. All…

A: To determine the vertical and horizontal force acting in the pipegiven the flow rates, pressure,…

Q: can this be done using simpsons rule?

A: As already calculated using the relation for the volume ranging from to in steps of , the…

Q: 20. How much force must be applied to push a 1.35 kg book across the desk at constant speed if the…

Q: 4- The logarithmic decrement can be obtained as 8 = In-*, is it possible to get a negative value of…

A: The logarithmic decrement is used to find the damping ratio of an under-damped system in the time…

Q: A B 15% M M1 M2 5% 40% D 20% E 20% G H 40% M3 I 10% 60% F J 90% M4 K 15% Knowing that: * flow L…

A: Given:

Q: A local shop is maintained at 101.3 kPa and 19oC. The air inside the shop is forced to leave at a…

Q: identify five areas for improvements to enhance productivity and or the overall performance within a…

A: Five areas for improvement to enhance productivity and or the overall performance within a polymer…

Q: describe the sequences of five production steps and stages from the initial research and development…

A: Given:Describe the sequence of five production steps and stages from the initial research and…

Q: h 0 a) How far down the slope will they land? r b) How long will they be in the air? t Vo m at an…

Q: Knowing that: flow L denotes an OK (sellable) output; flows C, E, I, and K denote NOK (scraped)…

A: Given:

Q: (b) Using the provided data: cross-section width w= 12 mm, cross-section hight h=98 mm, ● length of…

Q: Describe a gas ignition system

A: Ignition-The meaning of the word "igintion" is the action of starting to burn or making somethin to…

Q: If P=9.8kN Determine the reaction forces at Supports A and D

Q: 2) a) A container filled with water (p = 1000 kg/m³) sits on a scale. The scale shows a reading of…

A: a) original scale reading=15.0 N

Q: A Cavo loader has a hopper volume of 1 m3. The loader works for 2 shifts (8 hr/shift) with 1 hour…

A: Given : The volume of hooper is The diatance is The Total output of one 8 hour shift is

Q: Problem 1-5: Determine the resultant internal loadings acting on the cross section at point B. 60…

Q: Problem 11.9 The cube of material shown in Problem 11.8 (reproduced below) is subjected to a pure…

Q: determine the value and the location of the maximum shear stress in the section. In Figure Q2, a =…

A: Given : The shear force in this section is The diagram is,

Q: A three-blade propeller of a diameter of 1.5 m has a rotational speed is 60 Hz, the activity factor…

A: Given:the diameter of the propeller is The rotational speed is The activity factor is The static…

Q: Determine the centroid of the area shown by direct integration. 185 y 3/₂ = kx¹/2 ^y₁ = mx )a. )b. b

Q: For Air: y = 1.4 Question B1 a) With the aid of sketches give a clear account of the operation of…

A: To calculate the mass flow rate, calculate area ratio, back pressure drawing

Q: A single-stage axial flow pump with outer radius r2 =0.240 m and inner radius r1=0.120 m is given.…

Q: Complete the following hands-on activity involving the construction of the traditional unit cells of…

Q: Fluid dynamics: Potential flow

A: The objective of the question is to propose a complex potential function to represent the flow field…

Question

2.5 please help

Problem 2-5:
The rectangular plate is subjected to the deformation shown
by the dashed line. Determine the average shear strain Yxy in
the plate.
A
150 mm
B
3 mm
200 mm
3 mm
X

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the given variable

VIEW

Step 2: Calculate the average shear strain in the plate.

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
An element of material in plain strain is subjected to shear strain xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 30°. (b) Determine the principal strains of the clement. Confirm the solution using Mohr’s circle for plane strain.
A material is subjected to the following strain system,ex=200x10-6, ey=-56x10-6,yxy=230x10-6. Using graphical method, determine A. The principal strains B. The directions of principal strain axes C. The linear strain on an axis inclined at 50o counter clockwise to the direction of ex Given that young's modulus for the material is 207GN/m2 and the poisson's ratio is 0.27, determine the principal stresses
(a) Determine the shear strain at corner A if the plate distorts as shown by the dashed line. (b) Determine the average normal strain that occurs along the diagonal AC and DB. 5 mm 2 mm 4 mm 2 mm IB 300 mm $2 mm D A 400 mm 3 mm
Determine the:1- Shear Strain2- Shear stress3- Friction Coefficient
QB3 TWO DIMENTIONAL STRAIN Three strain gauges were arranged in the form of a rectangular rosette and positioned on a test surface. The measured strains were as follows: E1 = 200x 106 E2 = 100 x 10-6 E3 = 50 x 10-6 Determine a) the principal strains and the principle stresses b) the direction of the greater principal strain relative to gauge 1 and sketch the Mohr strain circle. Take the Young Modulus of Elasticity value to be E = 200 GN/m² and Poisson's ratio u = 0.28.
The strain components E, Ey, and yyare given for a point in a body subjected to plane strain. Using Mohr's circle, determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear strain at the point. Show the angle 0p, the principal strain deformations, and the maximum in-plane shear strain distortion in a sketch. Ex = 440 µE, ɛ, = -810 µE, Vxy = -540 µrad. Enter the angle such that -45°s0,s +45°. Answer: Ep1 = Ep2 = Ymax in-plane prad Yabsolute max. prad 0, =
3. The rectangular plate undergoes a deformation shown by the dashed lines. Determine the shear strain ysy and Yy at point A. 0.01 in Zin. 0.02 in. -7 in. 7 in. 0.02 in.
The plate is deformed into the dashed shape shown in Fig. 2-6a. If in this deformed shape horizontal lines on the plate remain horizontal and do not change their length, determine (a) the average normal strain along the side AB, and (b) the average shear strain in the plate relative to the x and y axes.
A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σy = 4 MPa , tauxy = 3 MPa A. By using the stress transformation equation, draw a curve of the stress variation experienced by the stress element at the axis of rotation angle θ = 0-180°. Use the interval θ = 1°, with the x-axis and stress as the y-axis. Mark on the curve where the principal stress and maximum shear stress occur. Draw the three stress curves completely and neatly B. Draw the stress element along with the magnitude and direction of the stress at the angle where the principal stress occurs and at the angle where the maximum shear stress occurs. C. Write down the direction vectors of the orientation of the principal stress (n1, and n₂) and the maximum shear stress (nmax). Write it in unit vector form i and j. D. Prove that the value of the stress invariant (I1, and I2) using the principal stress is reached and prove that the orthogonality condition of the direction cosine is…
Q4 A three strain gages have been attached directly to a piston used to raise a medical chair, the strain gages give strains as Ea = 80 µ , Eb = 60 µ and Ec = 20 u . Determine the principal strains and the principal strain directions for the given set of strains. And Compute the strain in a direction -30° (clockwise) with the x axis. 45 Pump
The strain components ɛ, Ey, and yy are given for a point in a body subjected to plane strain. Using Mohr's circle, determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear strain at the point. Show the angle 0, the principal strain deformations, and the maximum in-plane shear strain distortion in a sketch. Ex = 300 µe, ɛ, = -710 pe, Vxy = -440 urad. Enter the angle such that -45°s0,s +45°. Answer: Ep1= pe Ep2= με Ymax in-plane = prad Yabsolute max. prad Əp =