Problem 2 For the circuit depicted below, the frequency of the source is w = 377 rad/s and the two coils have a coupling coefficient K = 0.8. j200 5Ω www Πωλ 4Ω 1020°V rms 11 j5Ω 1. Find the value of the mutual inductance M 2. Using mesh analysis, calculate the currents I₁ and 12 (rms phasors)

Problem 2 For the circuit depicted below, the frequency of the source is w = 377 rad/s and the two coils have a coupling coefficient K = 0.8. j200 5Ω www Πωλ 4Ω 1020°V rms 11 j5Ω 1. Find the value of the mutual inductance M 2. Using mesh analysis, calculate the currents I₁ and 12 (rms phasors)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2P: Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your...

See similar textbooks

Similar questions

Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your answers in both rectangular and polar form. (a) i(t)=5002cos(t30) (b) i(t)=4sin(t+30) (c) i(t)=5cos(t15)+42sin(t+30)
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
ESSAY: Describe what happens to the power in this RLC series circuit as the capacitance decreases. Explain in general terms why the observed change should occur. Understand the effects of basic electrical components on the average power of the system and the concept of power factor. Differentiate between average power and real power.
An rms voltage of 22.2 V with a frequencyof 1.00 kHz is applied to a 0.290-mH inductor. (a) What is the rmscurrent in this circuit? (b) By what factor does the current changeif the frequency of the voltage is doubled? (c) Calculate the current for a frequency of 2.00 kHz
PHASE RELATIONSHIP SINUSOIDAL( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
Clear my choice A capacitor is connected in parallel with a load of S= 6000 VA, and pf3D0.8 lag. The load is operating at 180 V and a frequency of 60 Hz. Calculate the capacitance value that will correct the power factor to pf=1. Select one: O a. 0.295 mf O b. None of them c. 0.354 mf O d. 6000 mf An 8 kVA motor operates at a 0.75 power factor, the real power is then: Select one: О 60 KW O 600 W O None of the Answers O 6000 W What term describes the maximum expected error associated with a measurement or a seńsor? 113 ) A ENG 12-A
QUESTION 3 An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current. O 450mA RMS O 544mA RMS O 352mA RMS O 206mA RMS
An inductive impedance made up of a resistor and an inductor has the characteristic that its currentadvances in phase to the voltage at the impedance A) lags in phase with the voltage across the impedance B) is in phase with the voltage across the impedance. C) None of the above
please write the complete solution and the topic is AC parallel circuits thank you A sinusoidal 50 Hz voltage of 200 V(rms) supplies the following three circuits which are inparallel (i) a coil of inductance 0.03 H and resistance 3 ohms,(ii) a capacitor of 40 microfaradin series with a resistance of 100 ohms, (iii) a coil of inductance 0.02 H and resistance 7 ohmsin series with a 300 microfarad capacitor. Find the total current supplied.