problem 5.3 Consider a steam power plant that operates on the ideal reheat Rankine cycle. The plant maintains the boiler at 5000 kPa, the reheat section at 1200 kPa, and the condenser at 20 kPa. The mixture quality at the exit of both turbines is 96 percent. Determine the temperature at the inlet of each turbine and the cycle's thermal efficiency. Answers: 327°C, 481°C, 35.0 percent High-P turbine Low-P turbine Reheater Boiler Condenser Pump

problem 5.3 Consider a steam power plant that operates on the ideal reheat Rankine cycle. The plant maintains the boiler at 5000 kPa, the reheat section at 1200 kPa, and the condenser at 20 kPa. The mixture quality at the exit of both turbines is 96 percent. Determine the temperature at the inlet of each turbine and the cycle's thermal efficiency. Answers: 327°C, 481°C, 35.0 percent High-P turbine Low-P turbine Reheater Boiler Condenser Pump

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter14: Ocean Thermal Energy Conversion And Ocean Salinity Gradient Energy

Section: Chapter Questions

Problem 5P

See similar textbooks

Similar questions

Steam enters a turbine at 15bar and 600°C with a rate of 0.371 kg/s. The steam expands to 0.08 bar with quality at 90%. Stray heat transfer and kinetic and potential energy effects are negligible. For operation at steady state, • the volume flowrate at the turbine outlet is m³/s, ⚫the power developed by the turbine is ⚫and the temperature at the turbine exit is kW, °C.
The inlet and exit temperatures of the air expanded at an adiabatic turbine are 50 Cand -30 C, respctively, while operating at a plant. The air enters the turbine with a volumetric flow rate of 25 L/s and at 450 kPa. Assume air behaves as an ideal gas with constant specific heats. Calculate the turbine power output (kW) at isentropic conditions if the turbine operates at isentropic efficiency of 75%?
1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheat pressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, mass flow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following: (c) theoretical thermal efficiency (d) the steam rate (e) heat rate of the cycle
A steam turbine is to operate on a simple regenerative cycle. Steam is supplied dry saturated at 40 bar, and is exhausted to a condenser at 0.07 bar. The condensate is pumped to a pressure of 3.5 bar at which it is mixed with bleed steam from the turbine at 3.5 bar. The resulting water which is at saturation temperature is then pumped to the boiler. For the ideal cycle sketch the process on the T-s diagram and calculate, neglecting feed pump work,The amount of bleed steam required per kg of supply steamThe thermal efficiency of the plantThe specific steam consumption
A turbine discharges 200 kg/h of saturated steam at 10.0 bar absolute. It is desired to generate steam at 250°C and 10.0 bar by mixing the turbine discharge with a second stream of superheated steam of 300°C and 10.0 bar.(a) If 300 kg/h of the product steam is to be generated, how much heat must be added to the mixer?(b) If instead the mixing is carried out adiabatically, at what rate is the product steam generated?
A steam power plant operates on the ideal Rankine cycle. The steam enters the turbine at 7 MPa and 550°C. It discharges to the condenser at 20 kPa. Determine a.) The heat transfer to the water in the steam generator in kJ/kg, b.) The net cycle work in kJ/kg, c.) The cycle thermal efficiency in %.
2-64 Nitrogen enters a steady-flow heat exchanger at 150 kPa, 10°C, and 100 m/s, and it receives heat in the amount of 120 kJ/kg as it flows through it. Nitrogen leaves the heat exchanger at 100 kPa with a velocity of 200 m/s. Determine the Mach number of the nitrogen at the inlet and the exit of the heat exchanger.
HMW-1 Regenerative steam power plant shown in figure below employs two feed heaters which are optimally placed such that cycle has the maximum thermal efficiency. The mass of steam generated is 16 kg/s. The feed water leaves each heater as saturated liquid at corresponding bleed pressure. Neglect the pumps work and find: a. Cycle thermal efficiency. b. Specific steam consumption. c. Mechanical efficiency of the turbine-generator gearing unit. Draw the equivalent (T-s) diagram considering an ideal cycle. 70 bar 450°C Gearing unit Generator 15 MW Turbine Super heater Boiler Condenser 0.07 bar Оpen heater Closed heater Pump Pump Throttling Valve
A turbine receives steam at the following state: pressure 1200 kPag, enthalpy 2875 kJ/kg, speed 33.3 m/s and elevation 30 m. The steam leaves the turbine at the following state; pressure 20 kPag, enthalpy 2152 kJ/kg, speed 100 m/s and elevation 0 m. Heat is lost to the surroundings at the rate of 29 kJ/s. if the rate of steam flow through the turbine is 0.24 kg/s, what is the power output of the turbine in kW? Assume steady flow conditions. O 598.01 O 112.52 O 143.52 O 165.56
B. A Carnot engine operates between two temperature reservoirs maintained at 200°C and 20 °C, respectively. If the desired output of the engine is 15 kW, as shown in Fig. below, determine the heat transfer from the high-temperature reservoir and the heat transfer to the low-temperature reservoir. TH-200°C On Engine QL T₁ - 20°C W 15 kW
A Carnot vapor refrigeration cycle operates between thermal reservoirs at 7°C and 28°C. The working fluid is saturated vapor at the end of the compression process and saturated liquid at the beginning of the expansion process. Determine the operating pressures in the condenser and evaporator, in bar, and the coefficient of performance for each of the following as the working fluid. (a) Refrigerant 134a (b) Refrigerant R22 (c) water (d) ammonia
1) A cylinder of volume 50cm made of Pyrex glass is full to the brim with acetone. Suppose the cylinder and acetone are warmed by 30°C. (Coefficient of linear expansion of glass, 3.2 x 10-6K-1 and acetone, 5.0 x 10-5K-1) i. Calculate the change in volume of the glass. ii. Calculate the change in volume of the acetone. ii. Will any acetone spill out of the cylinder? Explain.