Only solve d e and f :Problem 6- Analysis of a nozzle flow (The stators in a gas turbine are designed to increase the kinetic energy of the gas passingthrough them adiabatically. Air enters a set of these nozzles at 300 psia and 700°F with avelocity of 86 ft/s and exits at 250 psia and 645°F. The specific heat of air at the averagetemperature of 672.5°F is cp = 0.253 Btu/lbm-R.a. Create a schematic representation of the nozzle and draw the boundary of the systemneeded to answer the next questions. Include the mass and energy interactions across theboundary.b.Create a governing equation for this nozzle from the general energy balance equationand cross-out any terms that are likely to be irrelevant or have little contribution in theequation.C.Calculate the velocity at the exit of the nozzles (in ft/s)d.List the assumptions and approximations that were needed to solve this problem.Identify (sketch) the two states of the working fluid (entrance and exit) on both a P-vdiagram and a T-v diagram.e.f.Convert the outflow velocity to mph and comment on the validity of the results fromthis problem.

Problem 6-Analysis of a nozzle flow ( The stators in a gas turbine are designed to increase the kinetic energy of the gas passing through them adiabatically. Air enters a set of these nozzles at 300 psia and 700°F with a velocity of 86 ft/s and exits at 250 psia and 645°F. The specific heat of air at the average temperature of 672.5°F is cp = 0.253 Btu/lbm-R. a. Create a schematic representation of the nozzle and draw the boundary of the system needed to answer the next questions. Include the mass and energy interactions across the boundary. Create a governing equation for this nozzle from the general energy balance equation and cross-out any terms that are likely to be irrelevant or have little contribution in the equation. C. Calculate the velocity at the exit of the nozzles (in ft/s) d. e. List the assumptions and approximations that were needed to solve this problem. Identify (sketch) the two states of the working fluid (entrance and exit) on both a P-v diagram and a T-v diagram. f. Convert the outflow velocity to mph and comment on the validity of the results from this problem.

Problem 6-Analysis of a nozzle flow ( The stators in a gas turbine are designed to increase the kinetic energy of the gas passing through them adiabatically. Air enters a set of these nozzles at 300 psia and 700°F with a velocity of 86 ft/s and exits at 250 psia and 645°F. The specific heat of air at the average temperature of 672.5°F is cp = 0.253 Btu/lbm-R. a. Create a schematic representation of the nozzle and draw the boundary of the system needed to answer the next questions. Include the mass and energy interactions across the boundary. Create a governing equation for this nozzle from the general energy balance equation and cross-out any terms that are likely to be irrelevant or have little contribution in the equation. C. Calculate the velocity at the exit of the nozzles (in ft/s) d. e. List the assumptions and approximations that were needed to solve this problem. Identify (sketch) the two states of the working fluid (entrance and exit) on both a P-v diagram and a T-v diagram. f. Convert the outflow velocity to mph and comment on the validity of the results from this problem.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water vapor enters the steam turbine at 4000 kPa pressure, 500 ° C temperature and 6 m3 / h volume flow, as shown in the figure below. If the mass flow rate of the incoming water is 0.2 times the mass flow rate of the water with 500 kPa pressure and 200 ° C temperature from the outlet no.2, it comes out from the outlet no.3 with 30 kPa pressure and 0.85 dryness degree. Since the heat transfer from the turbine to the environment is 5000 kw, | a) Find the mass flow rate of the incoming water. b) Find the volume flow of water at the outlet no. 3. c) Find the power (kW) produced by the turbine. Note: Changes in kinetic and potential energies are negligible.
In an ammonia refrigerator , the pressure in the evaporator is 267. 58 KPa and the ammonia at is 0.14 dry while at the exit is 0.86 dry . During compression the work done per kg of ammonia is 20 ,000 kg .m . Calculate volume of the vapor entering the compressor per minute if the rate of ammonia circulation is 6.54 kg. The compressor has a volumetric efficiency of 90% and it runs at 150 rpm .The ratio of stroke to bore is 1 .Latent enthalpy of ammonia at based on its evaporating pressure is 320 Kcal per kg and its latent specific volume of ammonia based on its evaporating pressure is 0.436 m3 per kg .Specific volume of ammonia WITH PH DIAGRAM
The inlet temperature of an air compressor is T₁=300°K and the outlet temperature is T2-500°K. The compressor operates at a mass flow rate of 0.093kg/sec and the heat lost during the compression is 10kJ/kg. Assume that the air is an ideal gas with Cp=1.004 kJ/(kg°K). Calculate the mechanical power needed to be provided to the compressor shaft. Present your answer in kilo- Watts (kJ/sec).
3. Air enters a gas turbine system with a velocity of 105 m/s and has a specific volume of 0.8mkg. The inlet area of the gas turbine system is 0.05m. At exit the air has a velocity of 135m/s and has a specific volume of L.5 m/kg. In its passage through the rurbine system the specific enthalpy of the air is reduced by 145kj/kg and the air also has heat loss of 27kj kg. Determine 7. 1. The mass flow rate of the air through the turbine system 2 The exit area of the turbine 3. The power developed by the turbine systenm
3. Steam enters the turbine at the rate of 1.5 kg/s with enthalpy of 2300 kJ/kg and exhaust enthalpy of 1200 kJ/kg. Steam is extracted from the turbine at a rate of 0.87 kg/s for heating purposes with enthalpy of 2570 kJ/kg. What is the turbine work, in HP? draw a diagram and show full solution
In turbochargers a turbine is directly connected to a compressor. The power harvested by the turbine is used to power the compressor. In the figure below a turbine runs on steam and powers a compressor on air. Air can be considered a perfect gas with k = 1.34, R = = 300K and a mass flow 0.28 kJ/kgk = 1bar, T₁ = and Cp 1.02 kJ/kgK. The air enters the compressor at p₁ rate of mdot = 5.9 kg/s and exits at p2 = 5.2 bars. The steam enters the isentropic turbine at P3 = 2 MPa, T3 = 320°C and exits at p4 = 100 kPa. State 2 Isentropic Compressor State 1 Air-perfect gas T₁ = 300K P₁ = 1 bar W Answer: tubine = ? State 4 Isentropic Turbine State 3 Steam T3=320°C P3= 2MPa What is the enthalpy at state 2? Please enter your answer in kJ/kg
A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (i) Find the velocity at the nozzle exit. (ii) If the inlet area is 0.1 m2 and specific volume at inlet is 0.19 m3/kg, find the rate of flow of fluid (iii) If the specific volume at the nozzle exit is 0.5 m3/kg, find the exit area of the nozzle.
Steam at 1 kg / s mass flow enters a steam isentropic turbine at a pressure of 4 MPa, a temperature of 300ºC and a speed of 50 m / s, and leaves it at a pressure of 150 kPa and a speed of 200 m / s. . Note: T0 = 25 ºC, P0 = 100 kPa, T (K) = 273 + ºC a) Find the power produced by the turbine.b) Find the reversible power produced by the turbine.c) Find the isentropic efficiency of the turbined) Find the second law efficiency of the turbine.
Steam at 1 kg / s mass flow enters a steam isentropic turbine at a pressure of 4 MPa, a temperature of 300ºC and a speed of 50 m / s, and leaves it at a pressure of 150 kPa and a speed of 200 m / s. .Note: T0 = 25 ºC, P0 = 100 kPa, T (K) = 273 + ºC a) Find the power produced by the turbine.b) Find the reversible power produced by the turbine.c) Find the isentropic efficiency of the turbinec) Find the second law efficiency of the turbine.
Example A 5-hp fan is used in a large room to provide for air circulation. Assuming a well-insulated, sealed room determine the internal energy increase after 1h of operation.
17. A fully inflated tire has a volume of 15 ft3. The pressure and temperature of theair in the tire are 65 psia and 75 F, respectively. At this condition, the air intakeneedle is depressed for 3 s and then released. Treating air as an ideal gas and assumingsmall changes in the tire temperature and volume, Find the amount of air that leftthe tire. Assume a discharge coefficient of 0.61 and a flow area of 0.01 in2.
A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specific volume is 12.6 ft3/lb and the final specific volume is 3.25 ft3/lb. If the inlet suction line is 4 in. ID and the discharge line is 2.5 in. ID, determine (a) the change in flow work between the boundaries, ft-lb/min; (b) the mass rate of flow, lb/min; and (c) the change in velocity. Answer: (a) 324,000, (b) 15.88, (c) -12.9 fps