Problem 9: Three temperature sensors, shown below, indicate measured temperature with 8-bit binary values on their output lines, T, to T,. The block diagram below shows how to use multiplexer modules to allow an 8-bit microprocessor to read any one of these sensors using its data input lines, D, to Do, by issuing an address to the multiplexer. Four-input/ Temperature 8-bit mux out Microprocessor Sensor Data 1A-8A| T7 0 in D7 0 TY-8Y IB-8B T7 o Sensor 1 address IC-8C Sensor Address 2 out ID-8D No connection select a) What is the size of the Data in? b) What is the size of the address? c) What is the size of the select?

Problem 9: Three temperature sensors, shown below, indicate measured temperature with 8-bit binary values on their output lines, T, to T,. The block diagram below shows how to use multiplexer modules to allow an 8-bit microprocessor to read any one of these sensors using its data input lines, D, to Do, by issuing an address to the multiplexer. Four-input/ Temperature 8-bit mux out Microprocessor Sensor Data 1A-8A| T7 0 in D7 0 TY-8Y IB-8B T7 o Sensor 1 address IC-8C Sensor Address 2 out ID-8D No connection select a) What is the size of the Data in? b) What is the size of the address? c) What is the size of the select?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Microprocessors; Explain the LOOP instruction with a simple example program for 8086 microprocessor.
Q1) List the main internal elements of a microcontroller. And explain the function of each of them. Q2) What is the difference between the Von-Neuman Microcontroller Architecture and Harvard Microcontroller Architecture. Q3) Compare between the (EEPROM) and the Non-Volatile RAM - (NVRAM). Q4) What is the term “Complex Instruction Set Computer(CISC)” mean in the Microcontroller Architecture.
4) Design and draw these memory units with their control circuits. Explain operations. a) A single EPROM 2716 is used with an 8088 microprocessor so that this microprocessor will see only X bytes of memory between the address range of DF800 –DFFFF or DD800 - DDFFF instead of 1M byte that it expects. Draw this circuit. What are X bytes? Do not use 74138 decoders. b) Design and show a 16K x 16-bit memory circuit by using 8K x 8-bit RAMS. Explain its operation. Do not use decoder 74138 chip.
Write a Verilog code with testbench for 16-bit up/down counter with synchronous reset and synchronous up/down.If up/down is set the counter is up counter and if it is not set, the counter is a down counter. submit the module code, testbench code, and the simulation results. PLEASE EXECUTE CODE IN VERILOG
8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.
A frequency counter is gated on for 10 ms and counts 540 pulses from a periodic input signal . What is the input frequency? a) If the gate time is changed to 100 ms , approximately how many counts would you expect from the same source during the gate time? b) In what way does the change in the gate time affect the resolution?
A 9 bit asynchronous counter has a 128 - kHz clock signal applied. i) What the mod Number of this counter ? ii) What will be the frequency at the MSB output ? iii) Assume that the counter starts at zero.What will be the count after 6.15 input pulse?
Q2: Explain the role of Stack Register in 8086 Microprocessor.
Explain the importance of voltage regulation modules (VRMs) on a motherboard and their role in CPU performance.
1- What does the VoH parameter of a logic IC refer to? a) The highest permissible output voltage. b) The lowest output voltage recognized as logic 1. c) The highest output voltage recognized as logic 1. d) The highest output voltage recognized as logic 0.
Q5. A general analysis of the switch-mode inverter shown in the figure below is to be done. The switching frequency f,, which is also the frequency of the triangular signal is 1450 Hz. The de voltage, Va, is 600 V. Output voltage is sinusoidal voltage with a frequency equal to 50 Hz. TA ADA. TA- ADA- VAN (Figure 8-4 on page 203 from Mohan's Book) a. Find the frequency modulation ratio, mr. b. Why the frequency modulation is chosen as an integer? c. Calculate the output voltage (rms value of first harmonic), when the amplitude modulation ratio, m., is equal to 0.8. d. Compute the rms values of the 5 most dominant harmonics of v4o at m,=0.8. e. Also indicate the frequencies at these harmonics you have found in part d appear.
Discuss the importance of VRM (Voltage Regulator Module) on a motherboard and its impact on CPU performance.