PROBLEM4:A brick with a mass of 3 kg falls from a height of 2 m onto a concrete block with a mass of 28 kg and sticksto it. The concrete block is held in place by four springs, each with a stiffness of 800 N/m. determine:(a) The differential equation of motion(b) The maximum displacement and the time of its occurrence.PROBLEMS:kmm3 kg28 kg}kmm2 m-Fu(t)Figure 4- Figure of problem 4

Answered: Image /qna-images/answer/0646cc1e-9811-497d-9ca1-3ec39fe8167a.jpg

Answered: The differential equation of motion The…

Engineering

Mechanical Engineering

The differential equation of motion The maximum displacement and the time of its occurrence.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A spring with stiffness constant k = 2000 N/m attached to a platform launched a mass of 2kg vertically in the air to some maximum height (measured from the equilibrium point of the spring). The spring was compressed by 0.3 meters before launch. Due to internal friction of the spring, 10 Joules of energy was lost as the spring expanded. How fast was the mass travelling when it was at half of its maximum height? You must use g= 10m/s? for this problem or you will actually find it much more difficult to calculate. Hint: First solve the problem of finding what the maximum height is and then solve the problem of finding the speed at half of that height.
Please answer the following question A cigarettes dispenser requires a south African five-rand (R5) coin with a mass of 9.5 g to dispense one cigarette with a mass of 0.2 g. The design of such a cigarette dispenser is based on a helical spring, of negligible mass, which is found to extend 0.1 mm under a mass of 0.2 g. The spring can support a total mass of a coin. As the customer place money on the dispenser, the spring and coin system displace vertically through 4 mm and release. 1.1. Provide a schematic representation of the mass and spring system. 1.2. Calculate the frequency of natural vibration of the dispenser. 1.3. Determine the velocity of the coin when it is 2 mm below its resting position.
2. Consider the same general setup as in Problem 1, but with an additional distributed load along the beam. This distributed load is described by the function G(x) = -(3x²)j kN/m, z = [0, L] where the boldface type indicates that G is a vector. a) Draw an FBD of this system with the distributed load. b) The distributed load is measured to be -27ĵ kN/m at the end of the beam. Find the magnitude and line of action of the equivalent resultant force due to the distributed load G(r). c) Draw the FBD of this beam using the equivalent resultant force you found in part (c). d) If the force applied to the end of the rope is F = 17.5 kN, solve for the vertical reaction force at the support (Ry) and the mass of the beam per-unit-meter (m₂). Take the magnitude of the acceleration due to gravity to be g = 9.81 m/s².
igure 2. Assume that the rod is massless, perfectly rigid, and pivoted at point P. When the rod is perfectly horizontal, the angle 0 = 0, the displacement y 0, and the springs are in neither tension nor compression. Gravity acts on the system (e.g. on mass M). We assume that y is a small displacement. A mass M is attached at the end of the rod. DE only 225 Your tasks: X k 0 3k a F a M y A Derive an equation of motion for the system in terms of the angular displacement 0, and its derivatives (you should not have y or its derivatives in this equation.) B Derive an equation of motion for the system in terms of the displacement y, and its derivatives (you should not have or its derivatives in this equation. C Assuming there is no external actuator force F acting on the system, write down the total energy H of the system in terms of 0,0 and element constants. Derive an expression for the time derivative H of the total energy. D Transform the equation from part B, which is in y, to another…
SHOW YOUR STEP BY STEP SOLUTION. 1. Assuming that the displacement (x) resulting from the application of a force F at a point A is small, find the equivalent spring constant of the system that relates the applied force F to the displacement x. k- 2k
The mass attached to the end of a helical pull spring statically forces the spring to pull, and 100 mm static elongation in the spring references The same mass is attached to the end of this spring, and the mass is released vertically from a height of 0.6 meters how many times does the force on the spring increase according to the static loading state when it is released? 4.32 O 4.87 5.36 5.12 18110140 O 4.60
2- Two mass-spring systems A & B both have stiffness of k-10 N/m. The mass of system A is twice the mass of system B (mA=2mg= 1 kg), which system will oscillate faster? Why? Support your answer with a plot.
A fender is mounted on a automobile though dampers (to absorb collision energy) and springs (so that the fender can recover after low-speed collisions). During a crash-test, the automobile is moving at 2 m/s when its fender strikes a concrete barrier. The vehicle mass, m, is 1,000 kg. (In comparison, the fender itself is essentially massless.) The springs that mount the fender have a stiffness, k, of 1,000,000 N/m. y m barrier 1) Write a differential equation for the deflection of the springs when the fender is in contact with the barrier. 2) If the damping coefficient, c, is 30,000 N-s/m, what is the damping ratio of the mass-spring-damper system when the fender is in contact with the barrier? 3) For that damping coefficient, make a reasonably accurate sketch (with properly labeled axes) of the time-course of the force exerted on the barrier, starting from the moment of first contact. 4) Is there any value of the damping coefficient, c, that would yield no rebound of the vehicle from…
FBD: The mass of a pendulum is connected to a spring with a spring constant Kas shown in the figure. The spring stays vertical all the time with the help of a massless follower. The vertical distance between the fixed point O and the path of the massless follower is 2L. Use Newton's second law and find the equation of motion of the system in terms of 0. 762 mgbi Img 2L L bil Nig K 777777 P EMO = Jaz ->0₂ ?
Q1. (a) Write the differential equations for the mechanical systems shown below. (b) State whether you think the system will eventually decay so that it has no motion at all, given that there are nonzero initial conditions. Initial Condition : X1(t=0) = 0 *1(t=0) = 0 m/s X2(t=0) = 0 *2(t=0) = 3 m/s k2 m2 ks No friction No friction
A. A car's body has mass 100 slugs. This mass is supported by the car's 4 shock absorbers. The shock absorbers are identical vertical linear springs. Complete a FBD of the car's body (this would not include the car's wheels, axels etc. just the car's body) Each spring is compressed 1.25 inches. Determine the spring "k" value. Answer: 644 lb/inch. Find the compression of each spring if 4 people, each with mass 6 slugs, get into the car, Answer: 1.55" ii. iii.
Help | System Announcements PRINTER VERSION 1 BACK NEXT Chapter 08, Problem 063 The cable of the 1600 kg elevator cab in the figure snaps when the cab is at rest at the first floor, where the cab bottom is a distanced = 2.8 m above a spring of spring constant k = 0.30 MN/m. A safety device clamps the cab against guide rails so that a constant frictional force of 5.1 kN opposes the cab's motion. (a) Find the speed of the cab just before it hits the spring. (b) Find the maximum distance x that the spring is compressed (the frictional force still acts during this compression). (c) Find the distance (above the point of maximum compression) that the cab will bounce back up the shaft. (d) Using conservation of energy, find the approximate total distance that the cab will move before coming to rest. (Assume that the frictional force on the cab is negligible when the cab is stationary.) (a) Number Units (b) Number Units (c) Number Units (d) Number Units LINK TO TEXT LINK TO SAMPLE PROBLEM…