Q₁: An electron starts from rest at the negative plate of a plane- parallel capacitor separated by 2 cm and having a potential difference of 1500 V. How long does it take to reach a speed of 107 m/s and what position does it reach at this speed? Ans: 7 57x10-10 s; 0.38 cm.

Q₁: An electron starts from rest at the negative plate of a plane- parallel capacitor separated by 2 cm and having a potential difference of 1500 V. How long does it take to reach a speed of 107 m/s and what position does it reach at this speed? Ans: 7 57x10-10 s; 0.38 cm.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Related questions

Q: 7. The system of Figure 9.4 shows a 3-phase Y connected generator feeding a A connected load. If the…

Q: The switch in the network in Fig. compute i(t) for t> 0 and use this current to determine v (1) fort…

Q: G=1/R is called [Select] Y = 1/Z where Z is a complex impedance. Y is called [Select] [Select]…

A: Given, G=1R is called _____ and has units of Siemens (S). Y=1Z where Z is a complex impedance. Y is…

Q: Determine V, for the network Si 4.7 ΚΩ +12 V o V₂₁ GaAs 3.3 ΚΩ - 10 V

Q: 2. Based on the given figure 2, explain the working principle of the Repeaters. www Long cable w…

A: Repeaters are used in long-distance communication due to inherent noise in the transmission system…

Q: Explain how poles and zeros are important in a feedback control system and the differences between

A: In this question we will write about poles and zeros for feedback control system.....

Q: In mark = Show that a series LR circuit is a lowpass filter if the output is taken across the…

Q: how did you know the medium is a good conductor? The question gives us the conductivity but we…

A: Note: Please note that here student is having only doubt about the permittivity which is known as…

Q: Use the Laplace transform to find the i0 as shown in the figure if Vg(t)=25cos(10t) V.…

A: Power is the product of supply voltage and the supply current.

Q: A series motor has an armature resistance of 0.202 and a series field resistance of 0.30. It is…

Q: What will be the length of a 10 ohm wire, when the resistivity of the wire is 0.1 ohms-m and…

Q: electrolysis, there are 2 tanks connected in series where the current that flows is 5000 A. Each…

Q: Question 2 This system below is a model of a custom electric heating system: R₁- 120 V R2 1.…

Q: Delta-Star Power Transformer 22kV 0.4 kV, Current on 0.4kV side is 1500A CTs on 0.4 kV have ratio of…

A: Given that a delta star 22/0.4kV power transformer. Given CT ratio on 0.4 kV side = 500:1 Current on…

Q: H.W. a. Find the current ic for the circuit in Fig. 12. b. Sketch the vc and ic curves and phasor…

A: We need to find out the current for given circuit

Q: α (DC) for a transistor

A: BJT (bipolar junction transistor) A transistor having a three terminal made up of semiconductor…

Q: It is desired to limit the current in an 80-2 resistor to 0.5 A when it is connected to a 50-V power…

A: Brief description: In the above given question we need to calculate the value of unknown resistance…

Q: Suppose the memory of a computer is as follows (assume all numbers are represented in hexadecimal…

A: In little endian the last byte of binary representation is reserved first although in the big endian…

Q: 2. Sawtooth wave x(t) = t, 0 < t < 1, T = 1 Ao = 1/2, An= 0, B₁ = -1/πn for all n

A: Brief description: For the above given saw tooth wave we need to derive it's fourier series…

Q: 10-10. A 12-bit linear PCM code is digitally compressed into eight bits. The resolution = 0.03 V.…

Q: E7.17 The switch in the network in Fig. E7.17 moves from position 1 to position 2 at = 0. ANSWER:…

Q: Q2// Find the current at 10 2 by using thevenin's theorem? 292 122 10v +₁+ 592 VIL 1092 +₁+ 20v

Q: B. In a series of tests to determine the parameters of an eight pole, three-phase 3300 V, 50 500 kW…

A: B. From locked rotor test Z/ph= VI=336.6386.56=2.24 ohmP=3Iph2RphRph=3Iph2P=3×86.56212.24×103…

Q: The n-channel JFET and the D-MOSFET have very similar I-V output characteristics. Which of these…

A: JFET - Junction Field Effect Transistor It is a three terminal semiconductor device. The three…

Q: 0 Sketch v, for the network Vi 20 V -20 V Vjo M 9122 Vz = 8 V + 0.22 ΚΩ

A: We need to find out the output voltage for given circuit

Q: Explain about time graded and current graded system?

Q: Consider the circuit below. + VA + Va 2R VC Va is "small" ip Characteristics of nonlinear device: iD…

Q: Q1// Find I1, I2 & 13? Where Ri=1092, R₂-4022 & R3-2002 V₁-10v & v2-20v R₁ ww V₁ I ww R2 R3 ww V₂ I

Q: L { 1 3-4S + 3-2s s²+49 ·}

A: here we have to find the inverse laplace transform.

Q: The Synchronizing pulses are transmitted to keep the camera and the picture tube beams in step?…

A: In a monochrome television transmitter, the synchronizing pulses are transmitted to keep the camera…

Q: What is the purpose of polarity testing in order to properly perform paralleling of transformers?

A: Polarity test define the direction of the current. it helps the interconnecting the primary and…

Q: 8 For the transistor in the circuit shown, what is the Vce when Vin = VIN O OV* Vcc Rc R₂ ime 15V…

A: Given here BJT npn transistor based circuit and asked to find the collector - emitter voltage.

Q: Sketch v, for the network and determine the dc voltage available. 100 V Si Ge 4.7 ΚΩ 2.2 ΚΩ –100 V |…

A: The circuit diagram is shown below,

Q: The armature of a 4-pole, 136 slots shunt generator is lap wound with four conductors per slot. The…

Q: b) A transmitter is designed to transmit a signal S(t) Shown below, D=9 B/2 D/2 D B=2 -B/2 1. Give a…

A: SNR: It is the strength of the signal that is desired to background signal that is undesired signal.…

Q: Question 4: Determine the average power delivered and Power factor to network having the following…

Q: LAPLACE AND INVERSE LAPLACE TRANSFORM. 1. L {t² sin 3t}

Q: A circuit has a resistance of 20 Ω, an inductance of 0.3 henry, a capacitance of 20 µF and the…

A: As connection of elements are not given. Therefore I solved it by assuming they are connected in…

Q: The input voltage of a Boost converter is 10V, the duty cycle of the boost converter is 0.25. What…

A: Brief description: For the above given question we need to calculate the value of output voltage of…

Q: A series motor has an armature resistance of 0.2 ohms and a series field resistance of 0.3 ohms. It…

Q: Calculate the response of the system G(s) given the input u(t) s+1 G(s) = u(t)= 2 cos(t +20°)-4…

Q: Construct a 64x32 RAM using a 16x8 RAM cell.

A: According to the question, we need to construct a 64×32 using a 16×8 RAM cell

Q: For the circuit shown in the figure, the Mesh Equation for (mesh#3) 402 www 10V SV 502 www wwww € ΤΩ…

A: Given circuit,

Q: The electro-dynamometer type wattmeter is shown below and assuming the diode to be ideal, the…

A: Given circuit, Primary side supply voltage, Vs=200 V (rms) Secondary side peak voltage, Vm=1002 V

Q: 3.11. Consider a first-order AR process that is generated by the difference equation y(n) = ay(n-1)…

A: Given,The difference equation generated by first order AR process is,yn=ayn-1+wnWhere,a<1wn=σw2

Q: The shaft torque of a diesel motor driving a 100V dc shunt-wound generator is 25Nm. The armature…

Q: design a uncontrolled three phase rectifier

A: Uncontrolled three-phase rectifier: Rectifier is used to convert the AC signal into DC signal. When…

Q: V2 (s) For the network shown Figure 1, determine the voltage transfer ratio V₁ (s) gain, poles and…

A: Brief description: For the above given second order system we need to calculate the transfer…

Q: a. b C. d. Given parameters: R₁ = 20 MS2 R2 = 5 ΜΩ RD = 3.3 ΚΩ Rs = 2 kΩ Rsig = 10002 RL = 1.5 kΩ…

A: We need to find out transconductance, input and output impedance and voltage gain for given circuit

Q: MAB orque in pound-feet. The inrush current to a synchronous motor is 235 amp when it is started…

A: Synchronous motor depend on interaction of magnetic field stator and rotor. stator contain the three…

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

Q₁: An electron starts from rest at the negative plate of a plane- parallel capacitor separated by
2 cm and having a potential difference of 1500 V. How long does it take to reach a speed of
107 m/s and what position does it reach at this speed?
Ans: 7 57x10-10s; 0.38 cm.
2CO3 T
the cathode which in

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?
4. In what form is the energy of a capacitor stored?
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
Can current flow through a capacitor?
A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
An inductor is constructed by winding a coil of 100 turns around a magnetic core. The core is a cylinder with radius 0.5 cm and the core material has relative permeability of 1000. The coil covers a length of 10 cm. Determine the resulting inductance. Enter your answer in mH rounded to two decimal places.
A thin metallic foil is placed between the plates of a flat capacitor parallel to them. How does this affect capacity? What if you join a plate with a wire?
C) A 25 A electrodynamic ammeter is controlled by a spring having a constant of 5.7295x 10-6 Nm/rad. The full scale deflection is 110°. Determine the inductance of the instrument while measuring a current of 20 A. The mutual inductance at 0° deflection is 4 u H and the change in mutual inductance is linear with the deflection.
QUESTION 5 A 20 ohms resistor is connected in series with a capacitor of 0.01 farad and an emf in volts given by 40e-3¹ +20e-6. Assuming that the charge and current on the capacitor are zero at t=0, determine the charge and current at any time.