Answered: Q/ If the cross section of the femur…

Q/ If the cross section of the femur can be approximated as a circular tube, determine the state of stresses on the points A and B at section due to the loads as shown in figure

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Related questions

Q: A roadway sign that weighs Py = 11 kN is supported by a structural pipe with an outside diameter of…

Q: The state of stress at the point can also be represented in termsof the maximum in-plane shear…

A: False, The state of stress at the point cannot be represented in terms of the maximum in-plane shear…

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

A: Given:P=84 KNd=50 mm

Q: Determine the torsional stress in the thin-walled tube as shown:

Q: Determine the principal stresses at point A on the cross-section of the beam at section a-a

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

A: Given data: d=50 mmP=66 kN Need to determine the normal stress at point A.

Q: Q3) Show the state of stress at points A and B on the assembly at section 400 mm а-а. a 200 mm AB…

A: Write the given data: The load in the x-direction will produce twisting couple on the vertical…

Q: The members of the truss shown below have a cross-sectional area of 10,000 mm-. Determine the…

Q: Use Mohr’s circle to determine the principal stresses at the point. Also, find the corresponding…

Q: The members of the truss shown below have a cross-sectional area of 10,000 mm. Determine the…

Q: Determine the principal stresses, the maximum in-plane shear stress, and average normal stress.…

Q: Q 2: A cantilever beam has the profile shown so that it will provide sufficient clearances for large…

A: Given: The load is 115.33 kN. The T cross section is shown below:

Q: circular tube AB is fixed at one end and free at the other end. The tube is subjected to axial force…

Q: The pedal crank for a bicycle has the cross section shown. If it is fixed to the gear at B and does…

A: Given data: The magnitude of the force subjected on the pedal is; F = 50 lb. Draw the…

Q: - 540 mm 180 mm- 180 mm 60 mm → - B 30 kN

Q: 1: Stress in the left rod after its lower end is attached to the st

Q: The bolt is fixed to its support at C. If a force of 18 lb is applied to the wrench to tighten it,…

A: Given Data: The applied force is F = 18 lb. The length from force is l = 6 in. Diameter of shank is…

Q: Determine the stresses ox, Oy, and txy, and show them on a stress element. Determine the stresses…

Q: The forces P, and P, are applied to the post in the directions parallel to the x and y axes,…

A: Given: The length of post, L = 1000 mm = 1 m The diameter of post, D = 100 mm = 0.1 m The force…

Q: determine (a) the principal stresses at K, (b) the maximum in-plane shear stress and average normal…

Q: a) the principal stresses; and (b) the maximum in-plane shear stress.

Q: A machine having a mass of 9555 kg is supported by three solid steel rods arranged as showed in the…

Q: Determine the average normal stress developed on the cross section as shown in Figure 1. 600 kN

Q: Load P shown below can be applied at any point on the steel disc (r=40mm) shown below. For this…

A: Given

Q: The member has a cross section with the dimensions shown, and is subject to an internal moment Mof…

Q: Q3-cross-sectional area of 75 mm has a tensile force of 15 kN applied to it. Detemine the stress in…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: 1. The pipe shown below has a 1" outer diameter and a .125" wall thickness. Determine the state of…

Q: Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile…

Q: Q)The state of plane stress at a point is represented by the stress element below: A. Draw the…

A: Question (A) ,(B) & (C) is Solved here. For the other Parts, Please Post this Question again.

Q: The bar has a diameter of 60 mm. If it is subjected to the force components as shown in the figure,…

A: Given data d=60mm

Q: The state of plane stress at a on the element. Represent th on an element oriented 60°…

A: Given Data : σx=34 MPaσy=30 MPaζxy=20 MPa

Q: Determine the principal stresses in the cantilevered beam at points A and B.

A: Draw sketch of beam and divide shear force into horizontal and vertical components.

Q: The 0.97 in diameter rod is subjected to the loads shown. Determine the normal and shear stress at…

A: To find: The normal and shear stress at point B. Given: The diameter of the rod is d=0.97 in.…

Q: The horizontal force of P = 80 KN acts at the end of the plate. The plate has a thickness of 10 mm…

A: Given data as per question P = 80KN The thickness of plate =10 mm Area=10×200=2000 mm2 we know…

Q: Determine if the stress in the steel section, aluminum section, and bronze section are compression…

Q: Q2: Determine the state of stresses at point A on the cross section of the pipe shown in Fig. D=50mm…

Q: determine the normal stresses in rod 1 (0₁) in

Q: A 100-mm-diameter rod is subjected to the loads shown. Determine the principal stresses at point A.…

A: NOTE: According to Bartleyby's policy we shall answer only three sub-parts so kindly repost other…

Q: All members of the truss shown have a cross-sectional area of 500mm2 and all pins have a diameter of…

Q: The bar has a cross-sectional area A and is subjected to the axial load P. Determine the average…

A: Applying equilibrium conditions :∑ Fx=0⇒V-Pcosθ=0⇒V=Pcosθ∑ Fy=0⇒N-Psinθ=0⇒N=PsinθCross sectional…

Q: At a point in a stressed body the state of stress on two planes 45° apart is as shown below.…

A: Given:σx=8 MPaτxy=3 MPaθ=45o

Q: In the case of the infinitesimal elements shown in the figures, determine the normal and shear…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

Q/ If the cross section of the femur can be
approximated as a circular tube, determine the state
of stresses on the points A and B at section due to the
loads as shown in figure

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
The bolt shown on the picture is subjected to total tensile force of 90 kN. Determine the tensile stress at the body of the bolt and tensile stress at root of bolt. Find also the compressive stress at the head as the bolt bears on the surface to resist the tensile load.
Calculate the normal stresses at points A and B of the bracket caused by the 30-kN force.
7. Determine the stress developed in the Tensional Cord given that the cable's diameter is 0.6 inches and the bar weigh 6kips. Figure P-106 3 m 5 m 5 m E
100 kN and 200 kN to the rectangular column in the figureTwo forces act in intensity. A and B according to givenon the stress element by finding the stresses atshow.
800 N 120 N.m d = 8 cm 600 N Q /If the cross section of the femur can be approximated as a circular tube, determine the state of stresses on the 160 N.m points A and B at section due to the loads as shown in figure. T. = 22 mm n = 18 mm tu Sl'o = I