Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Determine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. R What foree is roquirod to punch a square hole (25-mm 25mm) in a plate that is 30 mm thick? The shear strength is 350 MNm2. Purcha 30 mm hc

Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Determine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. R What foree is roquirod to punch a square hole (25-mm 25mm) in a plate that is 30 mm thick? The shear strength is 350 MNm2. Purcha 30 mm hc

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
3) A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location. A 125 mm dia. 50-mm dia. 75 mm 25mm dia. 5000 N 150 mm 75 mm
Please answer with explanation. Question : These two shear pins have the same length and same cross-sectional area. Both are subject to the same external tension load. Which pin has the lower shear stress? O a. The solid pin on the left. O b. The hollow pin on the right. O c. Both pins have the same shear stress.
Given a 2m-length rod with 23.0 mm diameter what is the actual stress (in MPa) if axial load is 10.4 kN.
c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod is 325 kN/mm?, calculate the minimum thickness of the rod. Give your answer in AIE
Solution: 2 of 4 Problem 2: The short cylindrical block of 2014-T6 aluminum, having an original diameter of 0.5 in. and a length of 1.5 in., is placed in the smooth jaws of a vise and squeezed until the axial load applied is 800 lb. Given young's modulus 10.6x10 psi and Poisson ratio equal to 0.35. a) Determine the decrease in its length b) Determine its new diameter. 800 Ib 800 Ib Solution:
ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30KN. If Young's odulus for the alloy is 69GPa determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3
ure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30KN. If Young's odulus for the alloy is 69GPa determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3 Figure 1
Calculate the maximum stress of a cylindrical specimen of steel alloy having an initial diameter of 12.55 mm and 110 mm long is pulled in tension with a maximum force of 20 kN. Select one: O a. 61.59 MPa O b. 125.22 MPa O c. 161.68 MPa O d. 160.15 MPa
* Problem-based learning - Acquire enhanced problem-solving skills using critical thinking Two shaft 40 mm of diameter are connected by a flanged coupling. The flanges are fitted with 8 bolts on 140 mm bolt circle. The shafts transmit a torque of 900 N-m at 350 r.p.m. For the safe stresses mentioned below, calculate 1. diameter of bolts ; 2. thickness of flanges ; 3. key dimensions ; 4. hub length; and 5. power transmitted. Safe shear stress for shaft material = 63 MPa Safe stress for bolt material = 56 MPa Safe stress for cast iron coupling = 10 MPa Safe stress for key material = 46 MPa A belt 100 mm wide and 10 mm thick is transmitting power at 1000 rev/min while the large pulley rotates , The larger pulley diameter is 1 .8 times the smaller pulley which having 250 mm diameter. Calculate the maximum power that can be transmitted. When the distance between the two pulleys are 4 m
What is the design stress in psi of an ASTM A313, gage number 8 spring wire. The type of application requires a factor of 0.34 for the type of service. Round your answer to 4 significant figures.
A mild steel rod having a stress of 50 Mpa and having a diameter of 20 mm What is the force applied on it.