Q1.а.The dc motor with the shunt connection has the following parameters:Voltage terminal, VT = 240 VLine current, IL = 100 AArmature resistance, RA = 0.14 QField resistance, RF = 200 QAdjustable resistance, Radj = 0 to 300 QNo load speed, no = 1200 rpmThe internal generated voltage Ea and field current characteristics graph isshown in FIGURE Q1.300Speed = 1200 rimin250200150100500.00.250.50.751.001.251.50Field Current, AFIGURE Q1i.Calculate the no-load speed of this motor when Radj = 120 Q.ii.Calculate the full-load speed when the motor Radj = 120 Q.ii.Under no-load conditions, determine the range of possible speedscan be achieved by adjusting Radj?Internal generated voltage E, V

i)At no-load condition, Back emf, Eb0=280 VLine current, IL=100 ATerminal voltage, V=240 VShunt…

Q1. а. The dc motor with the shunt connection has the following parameters: Voltage terminal, VT = 240 V Line current, IL = 100 A Armature resistance, RA = 0.14 Q Field resistance, RF = 200 Q Adjustable resistance, Radj = 0 to 300 2 No load speed, no = 1200 rpm The internal generated voltage EA and field current characteristics graph is shown in FIGURE Q1.

Q1. а. The dc motor with the shunt connection has the following parameters: Voltage terminal, VT = 240 V Line current, IL = 100 A Armature resistance, RA = 0.14 Q Field resistance, RF = 200 Q Adjustable resistance, Radj = 0 to 300 2 No load speed, no = 1200 rpm The internal generated voltage EA and field current characteristics graph is shown in FIGURE Q1.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights. design the single-phase, full-wave, ac/ dc converter. show design specifications, the reason for DC motor selection. correct manual circuit, and correct automatic closed-loop control circuit
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
A 250 V series motor has an armature resistance of 0.2 ohm and a series-fieldresistance of 0.18 ohm. If the speed is 6oo RPM when the current is 32 amps.What will be the motor speed when the load is reduced so that the current is18 amps, under which condition the percent flux change is 50 % of the percentcurrent change.
• Q5/ in a DC motor. List and describe the types of losses that occur
Q4/B/ What are the principal characteristics of a series DC motor? What are its uses? Core Mc
A DC chopper is used in regenerative breaking mode of a dc series motor. The dc supply is 600 V, the duty cycle is 70%. The average value of armature current is 100 A. It is continous and ripple free. What is the value of power feedback to the supply ?
A trapezoidal BLDC motor has an armature resistance of 0.6 Ω phase and the voltage drop across conducting transistor is 0.6 V. Motor is operated in the bipolar mode. This motor runs at 2000 rev/m on no load drawing negligible current from 200 V DC input. at what speed the motor run when loaded to 5 Nm torque.to what value should the input voltage be reduced to lower the speed to 500 rev/m for the same torque.
A freewheeling DC motor is driven with 1000 rpm and a nominal load torque of 80Nm. The field circuit resistance is 200 and the armature circuit resistance is 0.2 O. The field coils are fed with a zero degree transmission angle through a single-phase fully controlled converter connected to a single-phase 240V source. The armature circuit is fed from a single phase 400V source through another fully controlled converter. Magnetic saturation has been neglected, the motor constant is given as 0.8 V - s / A - rad. Assuming that there is no fluctuation in armature and field current, find the control angle of the converter feeding the armature at nominal load. If you want to leave the question blank, click again on the option you marked.
A PWM signal is sent to a permanent magnet DC motor through an H-bridge circuit. The PWM frequency is 100 kHz, the DC voltage source is 16 volts, and the specification of the motor is given as: voltage = 16 volts, no load speed = 1500 RPM, holding torque = 2 Nm. a. Draw the voltage signal delivered to the motor when the duty cycle is 20% and 80% (at least draw for 5 periods). Calculate the speed of DC motor when the duty cycle is 20% and 80%. b. C. Estimate the output power when the duty cycle is 20% and 80%. Assume that the motor efficiency is 100%.
8. A dc series motor develops a torque of 20 Nm at 3 A of load current. If the current is increased to 6A, the torque developed will be (a) 10 Nm (b) 20 Nm (c) 80 Nm (d) 40 Nm
A 48kW, 600V, 1500 rpm separately excited dc motor is controlled by single phase semi-controlled converter. The resistance of the armature is 192 and of the field is 1450. The field circuit is controlled by a single phase fully controlled converter and its firing angle is set to 20. The AC supply voltage to the armature and field converters is a single phase 220V, 60 Hz. The voltage constant is 0.946 V/A rad/s. If the armature converter firing angle is 45 and the speed is 1200 rpm; calculate the armature current and the developed torque.
Q4) What is the effect in series motor if you assume V = Eb , with low resistance fielding winding ? a) b) The given information about series motor on full – load (with that the flux is proportional to the field current) is a ) takes ( 78A) and runs at (850 r.p.m) , the series winding resistance is (0.04 2) , with diverter in parallel with the field winding is a (0.18 2) and the armature resistance is (0.09 S2). ( 220 V Neglected the iron, friction and windage losses. Determine the efficiency , speed when developing full load torque ,the maximum efficiency .