Q1/Choose the correct answer: 1-The ***** construction is a one-piece structure which defines the overall shape of the car and incorporates the chassis into the body. A) Body over frame B) unibody C) subirame D) chassis 2- In the GDI engines, a ...... power output improvement can be achieved over traditional PFI D) 15% engines. A) 20% B) 25% C) 10% 3- In the HEV'S, the integrated power unit (IPU) is located. A) under the luggage compartment floor C) under the hood B) behind the rear seats D) both A and B TOS

Q1/Choose the correct answer: 1-The ***** construction is a one-piece structure which defines the overall shape of the car and incorporates the chassis into the body. A) Body over frame B) unibody C) subirame D) chassis 2- In the GDI engines, a ...... power output improvement can be achieved over traditional PFI D) 15% engines. A) 20% B) 25% C) 10% 3- In the HEV'S, the integrated power unit (IPU) is located. A) under the luggage compartment floor C) under the hood B) behind the rear seats D) both A and B TOS

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.2 Choose the correct answer 1- A collision avoidance system uses of the vehicle. to detect a vehicle or another object in front a) G-sensor b) siren c) radar d) light 2- A combustion chamber with the displacement of 900 cc and 100 cc in the clearance volume has a compression ratio of. ********* a) 8:1 b) 11:1 c) 9:1 d) 10:1
1. How many unknown support reactions are there in this problem? 40 Ib/ft A) Two forces and two couple moments B) One force and two couple moments C) Three forces D) Three forces and one couple moment 30 4 ft 3ft 2. A general system of forces and couple moments acting on a rigid body can be reduced to a A) single force B) single moment C) single force and two moments D) single force and a single moment 3. The three scalar equations . Σ Fκ-ΣFvΣ Μo-0 , are equations of equilibrium in two dimensions. A) Incorrect B) The only correet C) The most used D) Not sufficient
22 - A steel pipe with a cross section area of 100 cm2 is subjected to pressure along its axis. What should be the maximum compressive stress of the material from which the pipe is made so that the pipe can safely carry a load of 500 kg? A) 150 daN / cm2B) 150 N / cm2C) 15 N / cm2D) 50 N / cm2E) 5 N / cm2
In figure (2), the friction coefficient between the crate and truck top surface is (0.5). If the truck initially moves at a speed of 50 km/hr. Figure (2) 3) What is the minimum stopping distance that the truck can have with constant acceleration? a) 8.2 m b) 64.2 m c) 35.3 m d) 22.5 m e) 54.9 m f) 19.7 m 8) None of them
25 - In the plane truss system, the loading status of which is evident in the figure, the support reactions and all rod forces will be found. A is the fixed joint and B is the sliding joint. Single upload P = 35 kN, dimensions a = 1 m and bar numbers are given. Accordingly, S5 = ? A) 49.5B) 35C) 99D) 70E) 140
13. For Problems 1 to 3. Three forces were applied to the horizontal beam of negligible mass, as shown. What is the magnitude of the reaction force at support C? 8.0 KN 3.00 KN 3.00 kN 3 B A) 7.9 kN B) 8.5 KN 3m 3m C) D) 4 9.0 KN 9.7 KN
35 - An electronic device will be cooled by a fan with a volumetric flow rate of 0.34 m³/min. If the air density is 1.2 kg/m³ and the average speed of the air is not desired to exceed 100 m/min, what would be the outer diameter of the fan? a) 6.5cm B) 7.0cm NS) 7.5 cm D) 7.2cm TO) 8.0cm
Question 9 Listen The blade on a circular saw has a radius of 0.100 m from the center to the tip of one of the blade's teeth. The blade is initially rotating at 200 rad/s when it is unplugged. The blade slows down constantly and stops after 8.30 seconds. Through how many revolutions does the blade rotate as it slows to a stop? O A) 132 revolutions B) 83 revolutions C) 166 revolutions D) 264 revolutions Question 10 Listen A millstone is spinning with an angular speed of 16.0 rad/s. Within 8.0 seconds the angular speed is increased at a constant rate to 24.0 rad/s. Through how many radians does the millstone turn during the 8.0-second interval? O A) 15 radians B) 16 radians C) 2.6 radians D) 160 radians
6- A motorcycle starts from rest at s = 0 and travels along a straight road with the speed shown by the v-t graph. What is the position of the motorcycle when t = 5 s? c) 15 m/ s f) None of them a) 59 m/ s v (m/s) b) 12 m/ s e) 66 m/ s d) 47 m/ s v = 1.251 =5 v = -1+ 15 t (s) 10 15
97) in which one does the heat of fusion remain constant throughout the process?A) yellow copperB) steelC) glassD) pure copperE) bronze 101) Which data is used in designs where weight and energy are considered together?A) elastic modulus...B) yield strengthC) special strengthD) breaking strengthE) tensile strength
Two blocks move towards each other on the x-axis and collide head-on. they move together at the end of the collision. first block m1 = 10kg and to the right V1 = 15 m / s, second block m2 = 30kg ce V2 = 15 m / s. What is the kinetic energy lost in this collision? A) 3600 JB) 3375 JC) 9375 JD) 10000 JE) 375 J
15. Two point charges, initially 2.0 cm apart, experience a 1.0-N force. If they are moved to a new separation of 8.0 cm, what is the electric force between them? A) 1/16 N B) 16 N C) 1/4 N D) 4.0 N