Q2 /A: The 6-kg lever OA with 250-mm radius of gyration about O is initially at rest in the vertical position (0 = 90°), where the attached spring of stiffness k = 525 N/m is undeformed (unstretched). Determine the constant moment Mapplied to the lever through its shaft at O which will give the lever an angular velocity w = 3 rad/s as the lever reaches the position 0 = 60°. k- 525 N/m ww 375 mm

Q2 /A: The 6-kg lever OA with 250-mm radius of gyration about O is initially at rest in the vertical position (0 = 90°), where the attached spring of stiffness k = 525 N/m is undeformed (unstretched). Determine the constant moment Mapplied to the lever through its shaft at O which will give the lever an angular velocity w = 3 rad/s as the lever reaches the position 0 = 60°. k- 525 N/m ww 375 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The strings AB and AC connect 500-g mass A to the vertical shaft BC. When the shaft rotates with a constant angular velocity of 15 rad/s, the ball has circular motion in the horizontal plane with the strings having angles of ? = 55° shown in the figure. Find the tension forces at the strings AB and AC.
2. Consider the 5-1lb bar with length of 2½ feet and width of 2 inches. Small frictionless bearings are mounted to the ends, constraining the motion of the bar to the horizontal x and y slots. The bar starts at rest at positioned at 0= 45°. If an angular acceleration of 3 rad/s² is desired, what moment M must be applied to the bar? What are the reaction forces at A and B at that instant? Additional question: Does the width of the bar matter, or is it appropriate to consider the bar as a slender rod? Consider errors of less than 2% negligible.
Q2: The 5.5-kg lever OA with 250-mm radius of gyration about O is initially at rest in the vertical position (0 = 90°), where the attached spring of stiffness k = 100 N/m is unstretched. Calculate the constant moment M applied to the lever through its shaft at O which will give the lever an angular velocity w = 4 rad/s as the lever reaches the horizontal position = 0. Ans.: M = 2.95 N. CW k= 525 N/m 4 M 375 mm 200 mm 375 mm
The figure shows the cross section of a uniform 239-lb ventilator door hinged about its upper horizontal edge at O. The door is controlled by the spring-loaded cable which passes over the small pulley at A. The spring has a stiffness of 16.6 lb per foot of stretch and is undeformed when 8-0. If the door is released from rest in the horizontal position, determine the maximum angular velocity reached by the door and the corresponding angle 0. Answer: @max 4.2¹ rad/sec at 8-i
Your answer is partially correct. The figure shows the cross section of a uniform 174-lb ventilator door hinged about its upper horizontal edge at O. The door is controlled by the spring-loaded cable which passes over the small pulley at A. The spring has a stiffness of 12.7 lb per foot of stretch and is undeformed when = 0. If the door is released from rest in the horizontal position, determine the maximum angular velocity reached by the door and the corresponding angle 0. Answer: Wmax = www 4.2' 0.636 rad/sec at 0 = 58.49 O
6. The uniform ring of mass m = 10 kg and radius r= 0.5 m is hinged at O and can rotate freely in the vertical plane. If the ring is released with a clockwise angular velocity o = 4 rad/s from the position shown where OC is horizontal, determine the magnitude of the reaction at pin O the instant the disk is released. to
The small end rollers of the 8-lb uniform slender bar (length = 4 ft) are constrained to move in the slots, which lie in the vertical plane. At the instant when Angle theta = 30°, the velocity of roller A is 13 ft/s down the vertical slot. Determine the angular acceleration of the bar, the acceleration of mass center G and the reactions of points A and B, under the action ofthe 6-lb force P. Neglect the friction and the mass of the small rollers.
Determine the reactions at the pin support and the applied moment if the bar of figure (shown below) has a mass of 50 g. If θ is 15° and the angular acceleration is 20 rad/s².
The shown spool has a mass of 450 kg and aradius of gyration Gk=1.2 m. It rests on thesurface of conveyer belt for which the coefficient offriction m= 0.5. If the conveyer acceleratesat2 1.2m / S and the spools rolls without slipping,determine the tension in the wire and the angularacceleration of the spool
Q. The upper and lower arms of Porter governor are 0.25 m each and are pivoted 30 mm from the axis of rotation. The radius of rotation Is 130 mm. The mass of the ball and sleeve are 3 kg and 38 kg respectively. Find the effort and power of the governor.
When the angle θ = 90 °, the cylinder BE starts with a vertical force (F = 3210 N) Newtons on the platform. Also, the box (box) is 200 kg and the angular velocity (ω) of body AB is 9 (rad / s). First, treat the box and platform as a single body to find the following: The magnitude of the reaction forces at points B and D. Box aG acceleration in the x and y direction. Second, having progressed earlier, only found the following for the platform: Reaction force from the box on the platform. Minimum symbol minimum A request of the consonant (μs) to disallow the box.
4. The uniform slender rod has a mass m= 20 kg and length L = 0.5 m. As the frame accelerates forward the rod is held in the position shown at a steady angle 0 = tan (3/4) by the stop at A. Determine the magnitude of the reaction force at stop A if the acceleration is a = 6 m/s. A = a L. A