Q2-A:What is the value of N₁?A) 0.0298B) 1.2320C) 0.0885D) 9.0065C = [0 1] D= [0 0]The state-space representation of a system is given above. Find the transfer function of the given systeQ2-B:What is the value of D₁?A) 0.0032B) 3.2352C) 21.3424D) 0.1828A = 10Q2-C:What is the value of D₂?A) 7.9832B) 0.2578-2.404810.83333 -2.2381C) 0.8627D) 1.23892.2381] B =[-1117 0.5714]G₂ =ON₁D₂s² + D₂s +1

Given State-Space Matrices Aim:To calculate the transfer function of the…

Q2-A: What is the value of N₁? A) 0.0298 B) 1.2320 C) 0.0885 D) 9.0065 A = 10 А C = [0 1] D= [0|0] me state-space representation of a system is given above. Find the transfer function of the given syste Q2-B: What is the value of D₂? A) 0.0032 B) 3.2352 C) 21.3424 D) 0.1828 Q2-C: What is the value of D₂? A) 7.9832 B) 0.2578 C) 0.8627 D) 1.2389 0 -2.2381 B =[-1.117 0.5714] -2.4048 10.83333 -2.2381. G₂ = 5 N₁ D₂s² + D₂s +1

Q2-A: What is the value of N₁? A) 0.0298 B) 1.2320 C) 0.0885 D) 9.0065 A = 10 А C = [0 1] D= [0|0] me state-space representation of a system is given above. Find the transfer function of the given syste Q2-B: What is the value of D₂? A) 0.0032 B) 3.2352 C) 21.3424 D) 0.1828 Q2-C: What is the value of D₂? A) 7.9832 B) 0.2578 C) 0.8627 D) 1.2389 0 -2.2381 B =[-1.117 0.5714] -2.4048 10.83333 -2.2381. G₂ = 5 N₁ D₂s² + D₂s +1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 1: A) Derive the transfer function of the electrical circuits shown in Figure below and then show the output signal when the input is a unit step. V₁(s) Vc (s) V(s) elle Ls -18
Part II. Explain how to convert a transfer function to modeling State space and how to convert state space modeling to a function transfer. Use an example to describe all the steps.
If we are using the following cireuit to measure ECG signal, V* has I mV of 60HZ noise and ECG signal of +3mV, while V also has ImV of 60HZ noise on it but a - ImV ECG signal. What will be the size of Vout for the 60 Hz noise and for the ECG signal?
ASAP It is a type of diode where it operates as a variable resistor when heated. Your answer What is the modulation index in ideal condition of AM. Your answer A form of AM where a sideband is filtered after its carrier is eliminated. Your answer What is the form of AM that used to transmit video signals of the TV system? Your answer It is a circuit in the superheterodyne receiver that adds and subtracts the frequencies of the AM signal and the local oscillator frequency. It is the extent to which the amplitude of the carrier wave is varied by modulating wave.
What is the z-transfer function of the system
. . Find the output for the system represented by transfer function shown in figure (1-10) analytically
Derive the transfer function R(s) Suppose the equations given as X2-g21X1+923X3] X3-931X1+g32X2tg33X3 X4-G42X2+&43X3 There are four nodes X1, X2. X3 and X4 we shall now draw the signal flow graph using above equations: 931 942 933 932 943 1 oC(s) 921 X2 R(s)o- X1 923
Transformation from state-space representation to transfer function: [ num, den ] = ss2tf(A,B,C,D)
What is SNRQ, rounded to the nearest dB, that a 10-bit uniform quantizer is expected to have for a full-scale sinusoidal input signal? (a) 50 dB (b) 62 dB (c) 74 dB (d) 98 dB O (a) O (b) O (C) O (d) A Moving to the next question prevents changes to this answer. Type here to search hp %2:
for the signal Plot even and add of the Signal XcX/ -3 1 $ XC4) 3 below, Patreven andoed Ports (compents) 3 -1- t
a. Reduce the following block diagram into a single functional block and determine transfer function C(s)/R(s).b. Determine the range of K for stability for the system shown in the figure.
The shape of the circuit with one input (X) and one output (Z) is given. The next state and output are implemented with a PLA. Let's assume that the circuit is in state (QAQB=0). Draw the state diagram. If X = 00101101 is applied as the input sequence, find the corresponding output sequence Z.