Q2) For the state of plane stress given on the element below, construct a Mohr's circle. Use circle to determine (1) the principal stresses, (2) the principal stress direction, (3) the maximum in-plane shear stress and corresponding and normal stress. 100 MPa L.

Q2) For the state of plane stress given on the element below, construct a Mohr's circle. Use circle to determine (1) the principal stresses, (2) the principal stress direction, (3) the maximum in-plane shear stress and corresponding and normal stress. 100 MPa L.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Related questions

Q: 3.2) An isolated piston-cylinder contains 3 liters of saturated liquid water at a constant pressure…

A: Given: The volume of water, V = 3 litres The pressure of water, P = 200 kPa The work done by paddle,…

Q: The position x of a particle varies with time as x = at²-bt³. The acceleration of particle is zero…

A: Given, Position x of a particle as a function of time = x = a t2 - b t3 When position as a…

Q: When activated by the force P,the gripper on a robotic arm is able to pick up objects by applying…

A: When push or the pull applied on the object, then it has the tendency to change the state of the…

Q: 1. Gate AB in Fig. below is 15 ft long and 8 ft wide into the paper and is hinged at B with a stop…

A: Length of the gate, L=15 ftWidth of the gate, w=8 ftThickness of the gate, t=1 in =112ftWater…

Q: The steel shaft with two different diameters rotates at 4.5 Hz. The power supplied to gear C is 51.7…

Q: The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the…

Q: Two reservoirs are connected with a pipeline see figure 2. The first section of the pipeline from…

Q: Airplane A is flying horizontally with a speed of 218 km/h which is increasing at the rate of 4.8…

Q: An automobile engine has a valve spring is to be made of Fe, C, & Mn, to be oil-tempered, & to be…

Q: A: If the position of a certain body was (-13) unit according to X-axis, then it is moved to be…

Q: A Carnot engine has an efficiency 50% when its sink is at a temperature of 27°C. The temperature of…

A: As given in question, Efficiency of Carnot engine = η = 50% = 0.5 Sink temperature = T2 = 27 oC =…

Q: = Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake power is 28 kW…

A: Given Volume, V= 1.78 L = 0.00178 m3 Brake power, BP = 28 kW Speed, N = 2500 rpm…

Q: What is the distinction between Dirichlet and derivative boundary conditions?

Q: Which of the following heating system is known as umbrella system? (it works against natural…

A: Given Umbrella system heating system To find Supporting statement

Q: A 4 3 20 kN B D 3 4 12 kN с L

A: From observation of truss the member BD is zero force member. From method of joint analysis

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

A: The given force in vector is The position vector of the force can be determined as shown below.

Q: -Z/Zo 3 The density of air as a function of altitude above sea level is modeled as p(z) = poe` where…

Q: The driver of the truck has an acceleration of 0.48g as the truck passes over the top A of the hump…

Q: Calculate the polar moment of inertia of the following cross section about origin: Y₁ 30 mm 4 (A)…

A: Parallel Axis Theorem:- Let xc and yc be the centroidal axis and x and y are the other axis parallel…

Q: 4 An electric motor exerts a constant 10 N*m torque on a grindstone, which has a moment of inertia…

A: When an amount of force act at the edge of an object, then the product of the force acting on the…

Q: 2/90 The 70-m microwave transmission tower is steadied by three guy cables as shown. Cable AB…

A: Solution: Co ordinates of the points are : A = (0,0,70)B=(35,-25,10)C = (20, 50,0)D = (-40, 20,0)

Q: 1. Compute the maximum shearing stress and deflection of a helical spring made from bronze…

A: Given data: Number of turns = n = 20 wire diameter = d = 0.50 in mean coil diameter = D = 2 x 3 = 6…

Q: Determine the diameter of a solid shaft which will transmit 440 kW at 280 rpm. The angle of twist…

A: Shaft is designed on the basis of following two criteria:- Strength Criteria Induced torsional…

Q: In uniaxial loading the poisson's ratio is 0.30 and the strain in the x- direction is 250 x 10^-6.…

A: Given data : Strain in X direction εX=250×10-6 Poisson's ratio μ=0.3 Finding strain in Z direction…

Q: Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake power is 28 kW…

A: Given Volume, V= 1.78 L = 0.00178 m3 Brake power, BP = 28 kW Speed, N = 2500 rpm…

Q: Find the transfer function Z(s)X(s) for the system shown. hand written plz Z WHIMP су www N

Q: Q2-Consider a Carnot heat-engine cycle executed in a steady-flow system using steam as the working…

Q: A spring-mass system with m = 0.5 kg and k = 10,000 N/m, with negligible damping, is used as a…

A: Given data as per question m = 0.5 kg k = 10,000 N/m

Q: Q3) In some wind tunnels the test section is perforated to suck out fluid and provide a thin viscous…

A: Given Data : Number of holes = 12064 diameter of hole = 5 mm suction velocity Vs = 8 m/s Entrance…

Q: Q4: Compute the supplied heat (Q1) of a system that its thermal efficiency is 90%, and the work done…

A: Given data: Thermal efficiency is, ηth=0.90 Work done = W = 173 J To find: Supplied heat i.e. Q

Q: A p=2.4 m Problem 3/51 3/52 If the speed of the block shown with Prob. 3/51 is 4.5 m/s as it passes…

A: When an object moves in a linear direction, then the distance travelled by the object in a unit time…

Q: 12. A horizontal shaft AD supported in bearings at A and B and carrying pulleys at C and D is to…

Q: Mex 02: A turbocharged diesel engine has an exhaust gas flow rate of 0.15 kg/s. The turbine T P₁ T P…

Q: The mass center G of the 1405-kg rear-engine car is located as shown in the figure. Determine the…

Q: The space between two fixed plane surfaces is filled with SAE 15W-40 having Specific Gravity 0.89…

A: The pulling force required to move the plate is 1.85362 N.

Q: The five-bolt connection must support an applied load of P = 3800 lb. If the average shear stress in…

Q: A car having a mass of 2Mg strikes a smooth rigid sign post with initial speed of 30km/h. To stop…

Q: Q2: For Fig (1): A. Calculate specific enthalpy, specific internal energy. temperature and specific…

A: From steam table, At P=400 kPa,T=416.763 K,vg=0.462 m3/kg,hg=2738.057 kJ/kg,ug=2553.1 kJ/kg,vf=0.001…

Q: Car A rounds a curve of 172-m radius at a constant speed of 37 km/h. At the instant represented, car…

Q: A dead weight tester is a device commonly used for calibrating pressure gauges. Weight loaded into…

Q: = Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake powe 28 kW and…

A: Given Volume, V= 1.78 L = 0.00178 m3 Brake power, BP = 28 kW Speed, N = 2500 rpm…

Q: 32-Calculate the frictional pressure drop for a smooth steel pipe with the following…

Q: The velocity of a boat relative to a fixed-earth coordinate system is 12 m/s and is constant. The…

A: Given: Speed of the boat→Vb=12 m/s Length of the tow rope→L=15 m Initial angle→θ=30° Rate of…

Q: A cantilever beam of span /carries a concentrated load Pat its free end. Which of the following…

Q: 4- Calculate temperatures for nodes 1 to 6 which is the steady-state. h = 12 W/m² °C T₁ = 15°C

A: T=50°C∆x=∆y=25cmk=1.5W/m°Ch=12W/m2CT∞=15°C To-Find:- Temperatures for nodes 1 to 6 at steady-state…

Q: Water, initially saturated vapor at 4 bar, fills a closed, rigid container. The water is heated…

A: The heat transfer from the closed-rigid container is 407.09 kJ/kg.

Q: 02: A two-stroke diesel engine was electrically motored (non-firing operation) when the meter…

A: Given Brake torque, T = 120 N.m Speed, N = 600 rpm Calorific value, CV = 40.3…

Q: Answe rite the sentence on for 10 only 1- Mn Ni Cr, W, Mo, V are the most important elements that…

A: Given questions: 1. Mn, Ni, Cr, W, Mo, V are the most important elements that form austenite.2.…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

Q2) For the state of plane stress given on the element below, construct a Mohr's circle. Use circle
to determine (1) the principal stresses, (2) the principal stress direction, (3) the maximum in-plane
shear stress and corresponding and normal stress.
100 MPa
150 MPa
Tay - 50 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
3. (a) Using Stress transformation equations, determine the principal planes, the principal stresses, the maximum in-plane shear stress and the corresponding normal stress. (b) Solve part (a) using Mohr's circle. 100 MPa 75 MPa 150 MPa
Problem 2: A state of plane stress at a point on the surface of a structure consists of the following stress components: Ox = 18 ksi, oy = 24 ksi, and Txy = 15 ksi. Note that the stress components act in the directions shown on the element below. Ox Txy 24 ksi бу 18 ksi 15 ksi (a) Draw a complete Mohr's circle for this stress state. Clearly label the X and Y faces, the center C, and the radius R. (b) Using Mohr's circle, determine the stress components Ox, Oy, and Txy on an element rotated 25° counter-clockwise from the original element shown. Label all of these quantities on the circle. (c) Show all stresses from part (b) on a properly oriented stress element. Be sure to include all stress components acting on the element.
The thickness of the bracket is 0.75 in. Draw a neat Mohr's circle 3 kips for the state of stress at point K, and use the Mohr's circle to determine 30 K. 2.5 in. (a) the principal stresses at K, (b) the maximum in-plane shear stress and average normal 2 in. 5 in: stress at K. Sketch the answers on correctly rotated elements.
Problem 1: A state of plane stress at a point on the surface of a structure consists of the following stress components: Ox = 25 ksi, oy = 12 ksi, and Txy = 10 ksi. Note that the stress components act in the directions shown on the element below. Ox Txy 12 ksi 5 25 ksi 10 ksi (a) Draw a complete Mohr's circle for this stress state. Clearly label the X and Y faces, the center C, and the radius R. (b) Using Mohr's circle, determine the principal stresses, the maximum in-plane shear stress, and the normal stress that acts on the maximum shear stress plane. Label all of these quantities on the circle. (c) Calculate the orientation of the principal planes and the planes of maximum shear stress. Label all of these quantities on the circle. (d) Show all stresses from part (b) on properly oriented stress element(s). Be sure to include all stress components acting on the elements(s).
Mohr's Circle The major and minor principal stresses acting at a point are 80 psi compression and 20 psi tension. (a) Draw the Mohr's circle for this stress combination. (b) What is the maximum shear stress acting at the point, and what value of normal stress acts on the plane? (c) Determine the value of the shear and normal stress acting on a plane that is 30° from the major principal plane. kindly answer the following with a complete solution so that i can understand how to solve it. thank you
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 16 MPa in size. (a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element. (b) Determine the stresses σn, σt, and the magnitude of τnt and show them on a stress element that is properly rotated with respect to the x-y element. The sketch must include the magnitude of the angle between the x and n axes and an indication of the rotation direction (i.e., either clockwise or counterclockwise).
(a) Construct Mohr's circle for an element in a uniaxial state of stress (b) Use this Mohr's circle to derive the equation for the normal stress On and shear stress En on the n-face. The equations should depend on Ox and θ (c) Use the Mohr's circle to determine the planes on which the maximum shear stress acts. Sketch a properly oriented maximum-shear-stress element and indicate the normal and shear stresses acting on its faces. Ơn nt o, Note: for (b), the angle θ is between 0 and 90° and is positive