Q5/ A/ If a Class B push-pull each Tr. Has V CEQ = 50V Calculate Ic sat. ( rc = 500 0, re = 0) %3D %3D B/ For the Zener diode circuit if Pz max = 27W and Vz = 10V find IZmax C/ For the C.E voltage divider bias circuit shown below. 1- Draw the AC analysis for the cct. 2- Write the equations for Zi, Zo, Av, Ai |+ VCC R1 RC C2 C1 Ac o/p B Ac i/p Zo R2 RE СЕ Zi

Q5/ A/ If a Class B push-pull each Tr. Has V CEQ = 50V Calculate Ic sat. ( rc = 500 0, re = 0) %3D %3D B/ For the Zener diode circuit if Pz max = 27W and Vz = 10V find IZmax C/ For the C.E voltage divider bias circuit shown below. 1- Draw the AC analysis for the cct. 2- Write the equations for Zi, Zo, Av, Ai |+ VCC R1 RC C2 C1 Ac o/p B Ac i/p Zo R2 RE СЕ Zi

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Sketch current I vs, voltage V for the circuits below. The breakdown voltage of the Zener diodes are shown. Assume 0.6V for all diodes (including Zener diodes) in the forward bias region.
A Full-wave bridge rectifier Circuit contains 4 Germanium diodes Cuse the Constant voltage drop model with VD = 0.30) driving ac a Load resistance of 10 kur. An Source with a Peak value of 4ou at bottz Vortage Source with a applied to the Circuit. a DIS 2 Determine the de value of the output wave form Determine the value of the Capacitor In uf needed to limit the output ripple vortage to 0.5 V if the Peak output voltage is equal to Upic -2VD
Find the range of values that will keep the zener diode “on” (operating) in the figure. (Plot the Vy-Vi graph).
Show the downward shift of the output signal with the series capacitor and diode. Clampers or DC restorers are clamp a peak of a waveform to a specific DC level compared with a capacitively coupled signal which swings about its average DC level (usually 0V). If the diode is removed from the clamper, it defaults to a simple coupling capacitor– no clamping. What is the clamp voltage? And, which peak gets clamped? Why is this so? Produce a schematic diagram with LTspice schematic capture program. Voltage values: Capasitor value: 1000 pF DC offset: 0 V Amplitude: 5 V Freq: 1 KHz
The forward-bias voltage drop for the ideal diode in the following circuit is 0.7 volts. Sketch thevoltage transfer characteristic (Vout vs. Vin) and the current transfer characteristic (Iout vs. Vin) asVin is slowly swept from – 10 V to + 10 V.
Ideally, we want the voltage for a Zener diode to be constant in the breakdown region. What does this imply about the dynamic resistance in the breakdown region for an ideal Zener diode?
1) the transformer turn-ratio (N1/N2) =? / 2) the PIV rating of diode =? /3) average power dissipated in diode PD =? / 4) the value of filtering capacitor (C) required to give ripple voltage Vr=0.5v is ? / 5) if each diode has rf=15 ohm and for same vm =12v, the peak secondary voltage Vsp=? / 6) if D1 is open then the average output voltage Vo(avg)=?
h) Draw a generic transfer curve for a diode. Define breakdown voltage, zener region, threshold value of a diode and show these elements on the curve. i) Explain the conditions of cut-off, saturation and linear region of a transistor and show on the transfer curve j) What is avalanche current? Explain.
Draw the characteristic curve of the standard PN-coupled semiconductor diode.Specify the correct and reverse polarity zones on the curve and draw the appropriate connection shapes.After mark the critical points on this curve and explain what these points mean.
What are transferred electron devices (TEDs)? A Gunn diode, being one example of TED is atwo-terminal passive semiconductor electronic component, which is used in high-frequencyelectronics. Discuss the principle of operation of this diode with help of energy band diagram.
Negative Peak Clipper with bias circuit uses a germanium diode, with an input peak to peak voltage VPP=20 V and bias voltage VBias= 2.7 v. a) What is the function of the circuit? b) Draw the circuit diagram. c) Draw the input and output waveforms.
The reverse recovery time of diode is trr = 3 s and the rate off all of the diode current is di/dt = 30 A/s. The storage charge current QRR is?