Q6) The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure tap at station 1. The velocity at station 2 is 2 times that at station 1. Air with a density of 1.2 kg/m³ flows through the duct. A water manometer is connected between the stagnation probe and the pressure tap, and a deflection of Ah = 5 cm is measured. What is the velocity at station 2? ΔΙ Vertical Water J

Q6) The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure tap at station 1. The velocity at station 2 is 2 times that at station 1. Air with a density of 1.2 kg/m³ flows through the duct. A water manometer is connected between the stagnation probe and the pressure tap, and a deflection of Ah = 5 cm is measured. What is the velocity at station 2? ΔΙ Vertical Water J

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

y aer. A Pitot tube is used to measure the air flow rate in a eircular duct 8.5 m I.D. The "riowing air temperature is 65.5°C. The Pitot tube is placed at the center of the duct and the reading R on the manometer is 1.2 cm of water. A static pressure measurement obtained at the Pitot tube position is 2.0 cm of water above atmospheric. Take Cp 0.98,9ter ase press u = 2.03 x 10 Pa.s, if U- Ux ( 1-0.17). Calculate The velocity at the center and the average velocity. The volumetric flow rate of the flowing air in the duct
A fan is used to blow air (density=1.15 kg/m3) in a duct. A pitot tube is placed in the duct as shown. The static pressure in the duct is measured with a wall tap and pressure gage. Use the gage readings to determine the velocity of the air. note: Pitot tube is used to measure the air total pressure. Mind on the head to be calculated if it is already in air. x 103 Pa Ptot tabe 12 x 103 Pa
A centrifugal pump has a suction pipe with a diameter of 100 mm, and adelivery pipe with a diameter of 75 mm. When discharging 15 L s -1of water, the inlet water pressure recorded is a vacuum of 198 mm Hg. The delivery pressure gauge, placed at 200 mm above the pump inlet, recorded apressure of 0.95 bar. As a reminder:1 bar = 750 mm Hgdensity of water = 1000 kg m -3 Calculate the total head losses, Ht (i.e., the rise in total head) and considering that the measured input power is 3.2 kW, calculate thepump efficiency.
A pump has a 100 mm diameter suction pipe and a 75 mm discharge pipe The capacity is 15 L/s of water A water- mercury manometer is installed in the inlet which reflects a vacuum pressure of 198mm of Hg The mercury level on the suction side is 100 mm below the pipe centerline. The pressure gauge 200 mm above the pump iniet recorded a pressure of 0.95 bar. The measured input power was 3.2 kW Find the efficiency of the pump Select the correct response(s) 75.12 % 60 42 % 59 01 % 80.43 %
The air is measured at 20 deg. C and 679mm Hg. The duct diameter is 744 mm while the discharge diameter is 340mm The fan draws 4 m^3/s air and the static pressure measured is 2 cm water Determine the power output in kW Answer should be round off to 2 decimal places
Air velocity in a duct is measured as 38.2 m/s by a pitot tube. Density of flowing air 1.3 kg/m3. If the pressure difference recorded by the pitot static tube is 0.1 m of water, calculate the coefficient of velocity of the pitot static tube. A Figure or Free Body Diagram will be much appreciated. Thank you
Given: diameter of pipe in point 1 = 3.9indiameter of pipe in point 2 = 2.5inspecific gravity of the liquid = 0.79h(ft) = 0.60ftpressure at point 1 = 14.6 psiapressure at point 2 = 49 psiapump and motor efficiency = 66%diameter of pipe in point 4 = 4.5indiameter of pipe in point 5 = 2.3 inZ3 = 35ft With the schematic diagram of a pump, tanks, and piping determine the following:1) The velocity of the liquid at point 2 (ft/s)2) Pump work used by the liquid (Wpump U) (hp)3) Electric motor power in out (kW)4) In figure 3, the shaded (pink) in the U tube is mercury; determine y. specific gravity of mercury 13.75) Mass flow rate
The pressure of a reactor vessel can be adjusted bychanging either the inlet or outlet gaseous flow rate. Theoutlet flow is kept fixed as long as the tank pressure remainsbetween 100 and 120 psi, and pressure changes are treatedby manipulating the inlet flow control valve. However, if thepressure goes higher than these limits, the exit gas flow isthen changed. Finally, if the pressure exceeds 200 psi, a ventvalve on the vessel is opened and transfers the gas to a storagevessel. Design a control scheme that meets the performanceobjectives. Draw a process instrumentation diagram for theresulting control system
A commercial venturi meter is placed in a vertical pipe as shown below. Pressure gauges are located at section 1 and section 2 and the pipe and throat diameters are as indicated. Assume that Cd-0.97 and calculate the downward discharge of water corresponding to pressures p1=65 kPa and p2=40 kPa.. Also, calculate the velocity at section 2. 20 cm 1 0.4 m 2 10 cm
Venturi meter: Assuming Cd = 0.955 for venturi meter , rho = 1000 kg/m3 Orifice plate: Assuming for orifice plate, K = 0.601 and r = 1000 kg/m3
As an engineer, you are setting up an experiment to measure the airflow rate in a duct. Choose a technique and devices for the measurement. You are required to design/draw the set-up and demonstrate the calculation for themeasurement of flow rate. Please discuss the relevant principle involved and reason for selectingthe technique.
Sheet 1 Page 1 of 2 Q1/ An orifice meter is to be calibrated for the measurement of the flow rate of a stream of liquid acetone. The differential manometer fluid has a specific gravity of 1.10. The calibration is accomplished by connecting the orifice meter in series with a rotameter that has previously been calibrated for acetone, adjusting a valve to set the flow rate, and recording the flow rate (determined from the rotameter reading and the rotameter calibration curve) and the differential manometer reading, h. The procedure is repeated for several valve settings to generate an orifice meter calibration curve of flow rate versus h. The following data are taken. VALVEX Flow Rate V (mL/s) Manometer Reading h(mm) 62 10 87 15 107 20 123 138 25 30 151 1- For each of the given readings, calculate the pressure drop across the orifice, AP (mm Hg). 2- The flowrate through an orifice should be related to the pressure drop across the orifice by the formula. D = KPn Verify graphically that the…