Question 1 A beam is undergoing bending deformation, whose cross-section is shown in Figure Q1. a) Determine the cross-sectional properties Igx, lyy and Iyy. b) Determine the direct (bending) stress distribution in the section beam, produced by a positive bending moment, M,. The cross-section is anti-symmetric with centroid at the mid-point of the vertical web. No moment is applied about the y-axis, i.e. M, = 0. M, Figure Q1

Question 1 A beam is undergoing bending deformation, whose cross-section is shown in Figure Q1. a) Determine the cross-sectional properties Igx, lyy and Iyy. b) Determine the direct (bending) stress distribution in the section beam, produced by a positive bending moment, M,. The cross-section is anti-symmetric with centroid at the mid-point of the vertical web. No moment is applied about the y-axis, i.e. M, = 0. M, Figure Q1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The state of stress at a point is the result of two loadings as shown in figure. When acting alone, the first loading produces the 3 MPa pure shear with respect of xy-axis. The second loading alone results in the 4 MPa pure shear with respect to the x'y-axis. The angle between the two sets of axis is 30° as shown. If the two loadings act simultaneously then resultant (absolute) shear stress at that point with respect to x-y axis is MPa (in integer). 3 MPa st 1 loading 2 loading 4 MPa α = 30° x'
Current Attempt in Progress When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and Cis 0.18 in. In segment (2), the normal strain is measured as 1,550 µin/in. Assume L = 34 in. and L2 = 92 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. (1) L1 L2 Answers: (a) in.ôz = 0.0001426 in. (b) ej = pin./in.
A thin polymer plate PQR is deformed so that corner Q is displaced downward 1.3 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 64 mm, b = 100 mm, c = 80 mm, and Δ = 1.3 mm.
The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear strain Yxy in the plate.
Find the lightest S-shape for the beam shown if the working stress in bending is 120 MPa. What is the maximum bending stress in the beam selected? Lightest S-shape beam =Maximum bending stress (MPa) =
A thin triangular plate ABC is fixed on side AB. The plate is strained such that all straight lines in the plate remain straight after deformation and that apex C is displaced to point C'as shown. Compute the following: a) the normal strains ex, ey and the shearing strain yxy at point C based on small deformation theory b) the normal strain at point A in the direction of AC based on small deformation theory c) the normal strains ex, ey and the shearing strain yxy at point C based on large deformation theory A 30° -200 mm. 3mm C" 1 I 1 1 60° 4mm
For the stress block shown, what is OP2 if OP1 = 140 MPa (T)? A.60 MPa (T) 40 MPa B.60 MPa (C) C.20 MPa (C) D.20 MPa (T) Txy Which among the following is ALWAYS TRUE about the maximum in-plane shear stress? A.It acts on planes 450 from principal planes. B.It is equal to the absolute maximum shear stress. C.It is equal to the principal stress with higher magnitude. D.It acts on planes with zero normal stress. 120 MPa
6. Due to a loading, the plate is deformed into the dashed shape shown in the figure below. Determine (a) the average normal strain along the side AB, and (b) the average shear strain in the plate at A relative to the x and y axes. 0.13 in В 0.09 in 10 in A 12 in C
Three strain gauges are attached on the surface of the plane frame which is shown in Figure. The angle between each strain gauges are θº=69º. Reading from these gauges are: εa= 1100 μ, εb =305 μ and εc = -240 μCalculate:(a) The principal strains(b) The maximum shear strain
Q36 onlys Ratio of stress in part A and B
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.22 in. In segment (2), the normal strain is measured as 1,900 μin./in. Assume L₁ = 47 in. and L₂ = 91 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. Answers: (a) in.₂ = (b) £₁ = (1) L₁ i B (2) L2 in. uin./in.
A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0525-in. to new position Q' as shown in the figure. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 9 in., b = 1 in., c = 3 in., and Δ=Δ= 0.0525 in.