only part 1d) Question 1: Water enters a tube (shown below) at a flow rate of 6 lit/min and an inlettemperature of 60°C. The convection coefficient and temperature at the external surface ofthe tube are set to 50 W/m K and 10°C, respectively. Thermal conductivity of the tube wall is385 W/mK.la. Draw the thermal resistance circuit of the system1b. Derive the energy balance of the system1c. Calculate the heat transfer coefficients inside the tube1d. Calculate the heat loss occurring along the tubeWaterInternal diameter = 50 mmWall thickness = 5 mmLength = 50 cm

Answered: Image /qna-images/answer/a39f0eb4-5e51-4c02-b423-afd11e12383e.jpg

Answered: Question 1: Water enters a tube (shown…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.21P

See similar textbooks

Similar questions

Saturated steam at 3 atm will flow through a 3 in. Schedule 80 steel pipe. In order todecrease the heat losses to the surrounding air (at 20 oC) the pipe will be insulated. There are twotypes of insulating materials available, each with a thickness of 2.5 cm. Thermal conductivity ofinsulator A is 0.04 W/m.K and that of insulator B is 0.20 W/m.K. Both insulators will be used, inorder to have the least heat loss. Which insulator should be covered outside? Assume thatconvective heat transfer coefficient between the insulated pipe and air is 15 W/m2K.
High-pressure steam condenses at 400 K on the outer surface of a thin-walled tube of 50 mm diameter. The overall heat transfer coefficient between steam and air on the inside of the tube is 200 W/m?. If the air enters the tube at 25 m/s, 150 kPa and 280 K, find the length of the tube required for the air to be heated to 350 K. [Ans. L = 13.9 m]
Answer this ASAP The diameter of the tube is 25 mm. The specific heat of water is 4.18 kJ/kg.°C. The overall heat transfer coefficient is 0.7 kW/m².°C. 1. Schematic of temperature distribution 2.ΔTLMTD 3.Actual heat transfer rate 4.Cmin 5.Maximum heat transfer rate
Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. flow rate q. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
Answer this ASAP The diameter of the tube is 25 mm. The specific heat of water is 4.18 kJ/kg. °C. The overall heat transfer coefficient is 0.7 kW/m².°C. 1.Cmin 2.Maximum heat transfer rate 3.Heat transfer surface area
Q2:- A sphere made of pure copper, which is 13 mm in diameter, is 70 °C (at t=0) when it inserted into a gas having a temperature of 25 °C. After 65 s the temperature of the sphere reach 60 °C. Make the appropriate assumption to find the heat transfer coefficient of the gas. What is the temperature of the sphere after 80 s. (A;=TT D2, V= TT D³/6, Lc=V/ A,)
1. Heated air at 1 atm and 35°C is to be transported in a 150-m-long circular plastic duct at a rate of 0.35 m³/s (Fig. 1). If the head loss in the pipe is not to exceed 20 m, using the Colebrook equation and consulting with the FE Reference Handbook and appropriate table(s) for equations and properties. Write a Matlab code to determine the i. ii. iii. iv. minimum diameter of the duct, the friction factor, average flow velocity and Reynolds number of the flow 0.35 m³/s air D -150 m Fig 1
a. An air stream passing through a 2-inch (1/6 ft) diameter, thin-walled tube is to be heated by high- pressure steam condensing on the outer surface of the tube at 320 °F. The overall heat transfer coefficient, h between steam and air can be assumed to be 25 Btu/(ft2.hr °F) with the air entering at 100 ft/sec, 10 psia, 40 °F. The air is to be heated to 150 °F. Determine the tube length required. Assuming Rayleigh Line flow, calculate the static pressure change due to heat addition. Also, for the same inlet conditions, calculate the pressure drop due to friction, assuming Fanno flow in the duct with f = 0.018. b. c. d. To obtain an approximation to the overall pressure drop in this heat exchanger, add the two results. Discuss the accuracy of this calculation.
For Heat transfer through cylinder tube wall, the temperature is to be a linear function of r (radius) of the tube. Select one: O True O False The conductivity of H20 in solid form (ice) is higher than that of H20 in liquid form (water). Select one: O True O False F, (Correction factor for temperature in some heat exchangers) should be 1.0 or greater than 1.0 in some cases. Select one: O True False
Conduction 1. A thermodynamic analysis of a proposed Brayton cycle gas turbine yields P= 5 MW of net power production. The compressor, at an average temperature of T. = 400°C, is driven by the turbine at an average temperature of T₁ = 1000°C by way of an L = 1m-long, d= 70mm - diameter shaft of thermal conductivity k = 40 W/m K. Compressor min T Combustion chamber Shaft L Turbine Th out (a) Compare the steady-state conduction rate through the shaft connecting the hot turbine to the warm compressor to the net power predicted by the thermodynamics- based analysis. (b) A research team proposes to scale down the gas turbine of part (a), keeping all dimensions in the same proportions. The team assumes that the same hot and cold temperatures exist as in part (a) and that the net power output of the gas turbine is proportional to the overall volume of the device. Plot the ratio of the conduction through the shaft to the net power output of the turbine over the range 0.005 m s Ls 1 m. Is a…
The steel pipe has an internal radius of 50 mm., a thickness of 5 mm. and a length of 5 m. Inside the pipe, hot fluid with temperature 80 C flows inside the pipe and cold fluid with temperature 20 C flowing outside the pipe. Let k=285 W/mC and hi= 25 W/mC, ho= 10 W/mC. Find 4.1) Heat Transfer Rate (Q) 4.2) Temperature on both inner and outer tube surfaces...
n electric generator at a power plant produces energy by passing superheated steam from a high temperature container (reservoir), through a pipe connected to a series of fans, and then into a low temperature reservoir. As the steam passes across the blades of the fans some of the heat energy of the steam is transformed into mechanical energy, which turns the fans which in turn are connected to a generator, which in turn converts the mechanical energy into electrical energy. If the high temperature steam has a temperature of 412.1 K and the low temperature reservoir has a temperature of 105.4 K, what is the Carnot efficiency of this process?

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning