agepressure p. The wall thickness and inner radius of the vessel are t and r,lated byQuestion 1.20The yield stress of a material is 45 MPa. This material is subjected to the maximum normal stress o, and the minimum normal stress 03--0.4x0₁1. The magnitude of o, that will cause yielding according to the maximum shear stress criterion isO a. 45 MPaO b. 32.1 MPaO c. 22.5 MPaO d. 75 MPaStop sharing11 Proctorio is sharing your screen.O b. PO c. pr/(2t)O d. 2pr/t6HideONext pag

Yield stress of material = σy=45 MPa Maximum normal stress in material = σ1 Minimum normal stress in…

Question 1.20 The yield stress of a material is 45 MPa. This material is subjected to the maximum normal stress o, and the minimum normal stress 03- 0.4x0₁. The magnitude of o, that will cause yielding according to the maximum shear stress criterion is O a. 45 MPa O b. 32.1 MPa O c. 22.5 MPa O d. 75 MPa

Question 1.20 The yield stress of a material is 45 MPa. This material is subjected to the maximum normal stress o, and the minimum normal stress 03- 0.4x0₁. The magnitude of o, that will cause yielding according to the maximum shear stress criterion is O a. 45 MPa O b. 32.1 MPa O c. 22.5 MPa O d. 75 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The principal stresses at the critical point of a part were found to be as shown. Using the distortion energy theory, yielding will occur if: 300 MPa 300 MPa 300 MPa O a. the material's yield strength is less than 900 MPa. O b. the material's yield strength is less than 300 MPa. O c. None of these. O d. the material's yield strength is less than 450 MPa. O e. the compressive strength of the material is less than 300 MPa.
The principal stresses at a point in a critical section of a machine component are 60MPa, 5MPa and 40 MPa. For the material of the component, the tensile yield strength is 200 MPa. According to the maximum shear stress theory, the factor of safety is A. 1.67 B. 2.00 C. 3.60 D. 4.00
Q1. If the yield stress (oy) of a material is 375MPa, determine whether yield is predicted for the stresses acting on both the elements shown below using: P₁=-215 RF 330 (a) Tresca Criterion (b) Von Mises Criterion Q = 200 Element A Note: your values for P (vertical load on Element A) should be negative (i.e. corresponding to a compressive vertical load). Element B S=90
Clear my cholce What is the value of shear stress if the torque exerted on a 6 mm diameter brass specimen was 20 N.m.? TD J= 32 %3D T = 2J Select one: O a. 471.5 GPa O b. 127.234 MPa C. 471.5 kPa O d. 0.4715 GPa Clear my choice IVITY
The stress to strain ratio of a material within the elastic limit (i.e., E) is found 55 GPa during the tension test, calculate the yield strength if the modulus of resilience of that material is 4.5 MPa. Select one: O a. 703.56 GPa O b. 22.25 GPa O c. 22.25 MPa O d. 703.56 MPa
A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 10^6 psi. When the same specimen is used in a tensile test, the modulus of elasticity is found to be 12.2 x 10^6 psi. Find Poisson’s ratio for the specimen. a. 0.40 b. 0.95 c. 0.30 d. 0.33 Show complete solutions when answering
1- Rankin's theory of failure is applicable for following type of materials (a) Brittle (b) ductile (c) elastic (d) plastic 2- Stress concentration is caused due to (a) Variation in properties of material from point to point in a member (b) Pitting at 'points or areas at which loads on a member are applied (c) Abrupt change of section (d) all of the above (e) none of the above 3- Yield point in fatigue loading as compared to static loading is (a) Same (b) higher (c) lower (d) depends on other factors (e) none of the above. 4- Transverse fillet welded joints are designed for (a) Tensile strength (b) compressive strength (c) Shear strength (d) bending strength (e) torsional strength. 5. The stress represented by cos (t) belongs to which category? a) Fluctuating Stresses b) Alternating Stresses c) Repeated Stresses d) Reversed Stresses 6. If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category? a) Fluctuating Stresses d) Reversed…
Q1. Find the shear stress in aluminum and Steel TAI, TS Use: Gsteel = 85 GPa, GAI= 30 GPa Aluminum Steel D=150 mm D = 50 mm T = 3 kN.m 2.5 m 0.5 m
A state of stress at a point A is given by σx = 77 MPa, σy = 3.1 MPa, and τxy = 12 MPa. What is the maximum in-plane shear stress for the point A? Lütfen birini seçin: a. 70.7106 MPa b. 38.8497 MPa c. 83.0846 MPa d. 39.4498 MPa e. None
1- Rankin's theory of failure is applicable for following type of materials (a) Brittle (b) ductile (c) elastic (d) plastic 2- Stress concentration is caused due to (a) Variation in properties of material from point to point in a member (b) Pitting at 'points or areas at which loads on a member are applied (c) Abrupt change of section (d) all of the above (e) none of the above 3- Yield point in fatigue loading as compared to static loading is (a) Same (b) higher (c) lower (d) depends on other factors (e) none of the above. 4- Transverse fillet welded joints are designed for (a) Tensile strength (b) compressive strength (c) Shear strength (d) bending strength (e) torsional strength. 5. The stress represented by cos (t) belongs to which category? a) Fluctuating Stresses b) Alternating Stresses c) Repeated Stresses d) Reversed Stresses 6. If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category? c) Repeated Stresses b) Alternating…
. In a uniaxial tension test, a dog-bone-shaped specimen is pulled in a machine. During the test, the force applied to the specimen, F, and the length of a gage section, L, are measured. The true stress, O,, and the true strain, &,, are defined by: 0₁ = F (KN) L (mm) FL EI. A Lo : &₁ = In # where A and Lo are the initial cross-sectional area and gage length, respectively. The true stress-strain curve in the region beyond yielding is often modeled by: o =KE The following are values of F and L measured in an experiment. Use the linearized form of the above equation determining the value of the coefficients K and m that best fit the data. The initial cross-sectional area and gage length are 4 = 1.25.10 m² and Lo=0.0125m. 24.6 29.3 31.5 33.3 34.8 35.7 36.6 37.5 38.8 39.6 40.4 12.58 12.82 12.91 12.95 13.05 13.21 13.35 13.49 14.08 14.21 14.48
Table B2: Stress-strain data for uniaxial compression test on Sample Normal stress Uniaxial strain (%) Lateral strain (%) (MPa) 0.0 0.0000 0.0000 5.0 0.0319 -0.0150 10.0 0.0720 -0.0275 15.0 0.1025 -0.0425 20.0 0.1450 -0.0600 25.0 0.1755 -0.0725 30.0 0.2150 -0.0875 35.0 0.2455 -0.1025 41.0 0.2815 -0.1125 46.0 0.3125 -0.1209 52.0 0.3515 -0.1285 58.0 0.4000 -0.1325 (f) Based on the plotted curve, calculate the average/tangent Young's modulus and Poisson's ratio for this sample, at 50 % UCS?