QUESTION 2 A continuous beam ABCD having a uniformly distributed load of 15 kN/m on span BC and point load of 40 kN on span CD as shown in Figure 2. Assume A is a fixed support and B, C are roller support. El is constant. Am. 15 kN/m 40 kN 6m 9m B Figure 2: Continuous beam (Rajah 2: Rasuk berterusan) By implementing the displacement methods of analysis that you have learnt in Structural Analysis I, calculate the internal moment at each support of the beam: By using the method of moment distribution. Draw shear and moment diagrams for the beam.

QUESTION 2 A continuous beam ABCD having a uniformly distributed load of 15 kN/m on span BC and point load of 40 kN on span CD as shown in Figure 2. Assume A is a fixed support and B, C are roller support. El is constant. Am. 15 kN/m 40 kN 6m 9m B Figure 2: Continuous beam (Rajah 2: Rasuk berterusan) By implementing the displacement methods of analysis that you have learnt in Structural Analysis I, calculate the internal moment at each support of the beam: By using the method of moment distribution. Draw shear and moment diagrams for the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. The beam ABCD is fixed with simple support of B and C as shown in the figure below. When point A is 15 mm and point D is bent upward by 10 mm, find the loads P, Q to make point A and D equal to point B and C support points. P is acting on point A, and Q is acting on point D. The Flexible Rigidity tee is 2.5 X 106 Nm (Use Maucalay's method) 15 mm B -2.5 m تے 5m 25m 25m 10 mm
An 8 m simple beam is loaded with a 228 kN point load at the first third of its length. The cross section of the beam is shown below. If the allowable stress is 200 MPa the thickness of the cross section is constantly t - 18 mm C t Y ▼ 2 Find the dimension c of the cross section such that it will satisfy the allowable stress. Select the correct response: 318.329 mm 290.593 mm 355.903 mm 263.312 mm
W A L A Test beam Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. b Section A-A Strain gauge 1 Strain gauge 3 Strain gauge 2 B (b) Location of Huggenberger strain gauges a D Referring to the above figure, calculate the location of the centroid, the second moments and product of area for the cross-section if; • D = 67 mm • B = 41 mm • t = 2.41 mm. From these, calculate the position and orientation of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis). Also calculate the directions of the principal second moments of area. Next, graph as scale diagram of the cross-section and plot the neutral axis on that diagram in the correct location and indicate the direction of deflection for the same conditions
W A L Test beam Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 b Strain gauge 3 Strain gauge 2 B (b) Location of Huggenberger strain gauges a Referring to the above figure, calculate the location of the centroid, the second moments and product of area for the cross-section if; • D = 67 mm B = 41 mm t = 2.41 mm. From these, calculate the position and orientation of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis). Also calculate the directions of the principal second moments of area. Next, graph as scale diagram of the cross-section and plot the neutral axis on that diagram in the correct location and indicate the direction of deflection for the same conditions
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! For the frame shown, a 4QQT-N load is acting on member ABD at D. If the allowable material shear stress for is 4Q MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
The steel truss shown carries a downward vertical load of 14 kN at joint B. The diagonal members of the truss have an area equivalent to 250 mm^2, and the horizontal members are 300 mm^2. With the given conditions calculate the: a) Horizontal Deflection at E in mm b) Vertical Deflection at D in mm Esteel = 200 GPa
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1730 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 210 kip-ft, P = 13 kips, LAB = 3.8 ft, LBC= 5.7 ft. МА V A Answer: (a) VA = (b) VB= LAB P B in. in. LBC C X
The beam is loaded by two point forces P. The beam is assembled according to the cross-sectional view by nailing wooden parts with cross-sections of 50 mm x c = 220 mm and 25 mm x d = 260 mm. How large can the value of the load P be when the distance between the nails in the longitudinal direction of the beam is 100 mm, the cross-sectional area of the nail is 9 mm2 and their permissible shear stress is 110MPa? Then calculate the maximum stresses and shear stresses of the beam at that load when the distance between the articulated supports is L = 1.9 m and the length of the beam projections a = 1.3 m. Permissible shear force of one nail? kN Static torque of the cutting surface? mm^3 Maximum torque change in cantilever? kNm Cutting force of the projection? kN Magnitude of force P? kN Calculated with the obtained force P maximum normal stress? MPa shear stress maximum? MPa
Q - 1 ; Determine the deflection equation for beam supporting load shown in Figure below, also determine maximum deflection, flexural rigidity of the beam is EI. W R R 2 2
Problem 2: A beam is made of four rectangular boards nailed together as shown. Note that the nails at C are aligned horizontally, while the nails at D are aligned vertically. Each nail can support a shear force Fs = 100 lb, and the entire beam cross section is subjected to an internal shear force V = 710 lb. (a) Determine the maximum spacing, s, for the horizontal nails. (b) Determine the maximum spacing, s', for the vertical nails. in. 10 in. A 10 in. BL 1 in. KE 1.5 in. 1 in. 2 in.
A girder with rhombus cross section, b side length, as shown on figure 2 is used as a simply supported beam over a span of 100*b m with central load of 50kN. Determine: (a) an expression for the bending stress, (b) The value of the maximum bending stresses when b=100 mm. Figure Q2
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress iss =10 MPa. 500 N/m 1.5 b OB - x m 2 m 2 m Calculate the centroid of the cross section of the beam O (1.5b, 1.5b] O (1.5b/2), (1.5b/2)] O (0.(1.5b/2)] O (0,0) [(1.5b/2), 0] O (0, 1.5b)