Question / Mode shapes provide vital vibration response information used by designers inidentifying vibration and noise mitigation plans. Discuss two ways of how mode shapeinformation can be used during the product design process.? please answer the question very shortly. few senstece to be easy to memorize

Question / Mode shapes provide vital vibration response information used by designers inidentifying vibration and noise mitigation plans. Discuss two ways of how mode shapeinformation can be used during the product design process.? please answer the question very shortly. few senstece to be easy to memorize

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.8: Computer-aided Design And Computer-aided Manufacturing

Problem 4RQ

See similar textbooks

Similar questions

In the context of our teaching, which one of the below statements is mostly correct about in detailed design of a component? In the reporting, I do not need to include the reasoning for my design decision for a good quality report. I cannot use appendix, so I am struck with the word limit for reporting. For a good clarity, I should not explicitly report what are the key dimensions and their tolerances in the drawing and in the body of text. The word count limit for detailed design report is 160O.
hand written plz 6. Design for , that is, the load can be taken by other members or the effect of fatigue failure otherwise mitigated, until the failed component can be detected and repaired or replaced. This approach is common in aircraft structural design. 7. create variations in dimensions, which can affect wear and fatigue properties. 8. is often used as the starting point to identify the most important problems and the most likely causes. 9. is a type of failure mode identification test, which use one/two samples to establish multiple design inherent failure modes, and establish operating and destruct limits of a product. 10. concerns the improvement in reliability, during use, that comes from field data feedback resulting in modifications.
Which one of the below statements is mostly NOT correct about in creation of detailed design of component? The selection of material is based on what is required to performance the function. The tolerance is determined by the function, not the preference of designer or manufacture. In the selection of manufacturing processes, the number of components to be manufactured needs to be considered, as the capital investment needs to be considered. I do not need to show or prove the component is working: such how much electricity is generated in power panel, how much braking force is generated in by the brake disc, or how much the force the component in suspension is subjected?
Tolerance is .. Your answer Clearance is . Your answer Why it is important to generate a number of alternatives for each component or subassembly in configuration design? Your answer
What are some of the ways for improving the accuracy of FEA for 3D printed components? Select all that applies. A) Explicit modeling of the component B Analyzing the model as an assembly Using Non linear material model Using orthotropic material model
IL IOUJOICIICA RAGICated in the 2-Dirmensional views (Orthographic) is milimeters centimeters There is no way of teling meters 3. When yow stari investigating to salve technological problems the following Technologiool Process yes can be followed to find information: Compare exising products write o design brief perform practical tests both A and C plus collect data. 4.Jocolleci dota the folowing could be used as a resource: Sractical investigation and testing of oproduct A, Band C A speok to or inteniew people firnd infomclion irom any print medio 6. existing products will help technologists in 20
Please define specialty models and base
True or False a) “If the most conservative fatigue criterion were used for infinite life design, the first cycle yield check is not needed.” b) If an accurate value for the notch sensitivity is hard to find, I should consider the fatigue stress concentration factor higher than the stress concentration factor under static loading condition in design. c) It is easier to find the asymptotic value of fatigue strength as the endurance limit on the S-N curve for a brass alloy (Cu70Zn30) than that of endurance limit on the S-N curve for an AISI 1045 steel.
Dynamic
Define the term form factor?
Summarise the main principles of designing a part or component using a Computer Aided Design (CAD) tool such as Solidworks, i.e. how do you go about creating the CAD geometry? 2. (а) (b) Briefly explain what is meant by dimensions and relations in Solidworks, why these are used and how to control and manage these. (c) Briefly discuss aspects of good practice for the development of the CAD design file within the Solidworks software. (d) You have to re-design a low cost stackable foot stool. Suggest how the design could be developed to reduce costs.
Problem 2: Review the below link, and choose 3 practical examples to solve structural/performance-based issues using finite element product. Discuss what you understand from these examples. Use your own words. https://www.hitechfea.com/fea-projects.html hitech Since Your Partner in Digital Excellence 1992 SERVICES ✓ PROJECTS ✓ » FEA Projects CLIENTS FEA shortens the Design Cycle for Thermal Radiation Detector System for Power Plant BLOG ABOUT US CONTACT US Finite Element Analysis - FEA Projects / Case Studies Please review few of the FEA projects, FEA case studies and FEA work samples that represent the FEA solutions HiTech FEA engineers have provided to our global clientele from different industries. Simulation using ANSYS Professional NLS helps to reduce Product Development Cycle Effective Static Structural Services conducting Structural Seismic Analysis of RTO System Base