Questions 1. Steam from the turbine exhausts directly into the (shell/water) of the condenser. 2. As the steam flows down over the tube bundles it gives up (a) point, where it becomes liquid again. until it reaches the (b) 3. True or False a. The main steam condenser for a turbine is usually located below the turbine. b. One routine maintenance procedure frequently done inside a condenser is plugging tubes to clear them of blockage.

Questions 1. Steam from the turbine exhausts directly into the (shell/water) of the condenser. 2. As the steam flows down over the tube bundles it gives up (a) point, where it becomes liquid again. until it reaches the (b) 3. True or False a. The main steam condenser for a turbine is usually located below the turbine. b. One routine maintenance procedure frequently done inside a condenser is plugging tubes to clear them of blockage.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter47: High-pressure, Low-pressure, And Absorption Chilled-water Systems

Section: Chapter Questions

Problem 9RQ: The approach temperature for the evaporator is A. the difference between the suction and head...

See similar textbooks

Similar questions

The approach temperature for the evaporator is A. the difference between the suction and head pressures converted to temperature. B. the difference between the refrigerant boiling temperature and the suction-line temperature. C. the difference between the refrigerant boiling temperature and the inlet water temperature. D. the difference between the refrigerant boiling temperature and the leaving-water temperature.
Briefly explain what is meant by condenser splitting, and list its main advantage.
Please answer questions g, h, and i. g.Calculate the heat transferred in the condenser. h.Calculate the diameter of the pipe connecting the turbine to the condenser. Design data for the plant shows the following pipe diameters. i. Calculatecooling water flow rate in GPM (‘gallons per minute’)through the condenser if the temperature of the cooling water increases from 13 C to 24 C in the condenser.
Fill in blank appropriate Steam leaving the turbine passes through the of steam condenser which maintain at the exhaust of turbine. Option 1: Medium Pressure Option 2: High pressure Option 3: No Pressure Option 4: Low pressure Ouiek isetienn Prev View Next Summary
In all liquid refrigerant lines, the pressure at the bottom of a vertical rise isgreater than the pressure at the top of the rise. For R-134a, the pressure isabout 0.5144 lb/sq in or less for every vertical foot of pipe that is used. Thevertical rise between this condenser and evaporator is 7.5 feet. How muchless is the pressure at the top of the rise than at the bottom?
Ill leave a thumbs up if you answer the following. Determine the following: a. hf at the condenser temperature b. hfg at the condenser temperature c. Specific volume in cubic meter of the condensate d.Quality of the steam at the turbine exit
The cooling water flow through the condenser should be rather fast as fast as possible from the lower inlet to the upper outlet from the upper inlet to the lower outlet in either direction and velocity as long as there are no leaks
1. A temperature drop in the coolant entering the primary loop can be dangerous because,(a) Reactivity can increase as a result.(b) Pressure in the primary loop will decrease and water can flash to steam.(c) All of the above.(d) None of the above
Please calculate enthalpies and the heat of a condenser and evaporator. Thank you
Find the following: a. Enthalpy of the steam in kJ/kg entering the condenser b. Enthalpy in kJ/kg of the condensate c. Enthalpy in kJ/kg of the feed water
Note:Use-the relevant-chart-for-each-preblem------ 5. For a vapour compression refrigeration system using R-22 as refrigerant, condenser outlet temperature is 40°C and the evaporator inlet temperature is -20'C. In order to avoid flashing of the refrigerant, a liquid-suction vapour heat exchanger is provided where liquid is subcooled to 26°C. The refrigerant leaves the evaporator as saturated vapour. The compression process is isentropic. Find the power requirement and coefficient of 1 performance if capacity of the system is 10 kW at -20 °C. Show the cycle on temperature- entropy and pressure-enthalpy diagrams. The specific heat of vapour refrigerant is 1.03 kJ/kg K. (Same as Example 14) Please solve the question on a piece of paper and using tables with illustrations
Why is a plastic or metal restrictor placed ineither the end of the vent pipe or in the vaporvent hose on some vehicles?