Rotation of bar OA is controlled by the lead screw which imparts a horizontal velocity v = 39 mm/s to collar C and causes pin P to travel along the smooth slot. The velocity of collar C is decreasing at a rate of 5 mm/s² at the instant in question. Determine the values of and 0, wherer = OP, if h=155 mm and x = 115 mm. h Answers: 2.086 i .059 mm/s² rad/s²

Rotation of bar OA is controlled by the lead screw which imparts a horizontal velocity v = 39 mm/s to collar C and causes pin P to travel along the smooth slot. The velocity of collar C is decreasing at a rate of 5 mm/s² at the instant in question. Determine the values of and 0, wherer = OP, if h=155 mm and x = 115 mm. h Answers: 2.086 i .059 mm/s² rad/s²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The telephone-cable reel is rolled down the incline by the cable leading from the upper drum and wrapped around the inner hub of the reel. If the upper drum is turned at the constant rate w₁ = 2.8 rad/s, calculate the time required for the center of the reel to move 85 ft along the incline. No slipping occurs. 40" Answer: t = sec 12" 16" 001
Two spur wheels with involute teeth gear together externally. The pitch circle diameters are 120 mm and 300 mm and the smaller wheel has 19 teeth. The pressure angle is 20o and the addendum is 0,3 of the circular pitch. Determine 1.1 The length of the arc of approach if the smaller wheel is the driver, and 1.2 The maximum velocity of sliding between the teeth when the driver rotates at 200 r/min
Determine the angular velocity of the slotted link AC at this instant measured counterclockwise. The disk rotates with the angular motion shown. The peg at Bis fixed to tho disk. Suppose that w-6 rad/s, a= 10 rad/s, r=0.6 m, and a= 1.05 m. (Ekure 1) Express your answer using three significant figures. Enter positive value if the angular velocity is and negative value if the angular velocity is clockwise. wAC = 0 rad/s Subimil Previous Answers v Correct Figure 1 of 1 Part B Determine the angular acceleration of the slotted link AC at this instant measured counterdockwise. 30 Express your answer using three significant figures. Enter positive value if the angular acceleratie counterclockwise and negative value if the angular acceleration is clockwise. AE it vec rad/s Submit Previous Answers Request Answer
The rod OA rotates clockwise at a constant angular velocity of 0 = (3) rad -. Two pin-connected slider block, located at B, move freely on OA. The curved rod is described by the equationr = (250 · (8 - cos 0)) m. Hint: 1. Remember clockwise rotation is negative velocity. A d3 d1 d2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value 01 130 degrees di 0.45 m d2 dz 0.2 m 0.325 m Using cylindrical components, a. Determine the cylinders's radial and transverse components of velocity at the instant shown, vr and b. Determine the cylinders's radial and transverse components of acceleration at the instant shown, a, and ag. c. Determine the cylinder's magnitude of the velocity at the instant shown, v d. Determine the cylinder's magnitude of the acceleration at the instant shown, a
α v= A t = B Oh no! A very sad kitty is trapped on a little platform connected to a gear system, the little scoundrel! The cat is 10 feet below the cliff's edge and is too terrified to jump! Quick! Rotate the wheel at A at 4 rad/s to raise the poor creature to safety. At what speed does the platform raise? How long will it take the kitty to reach the top of the clliff's edge? The diameter of the crank and gears are dд = 1 ft, dß = 2 ft, dc = 6 ft, and dp = 2 ft D ft S www S
Link BC (of length 0.47 m) is pin connected at the fixed point C and makes an angleof ⍬ = 51° with the vertical. This link is connected to the vertical link AB (of length0.3 m) and point A is also the axle of a wheel of negligible size that is moving alonga circular track of radius r =2.3 m. If the speed of A is constant and VA = (-2.59)im/s, which one of the following statements is correct? (In the followingstatements, wAB and wBC denote ⍵AB and ⍵BC respectively, where both are definedpositive in the k-direction and given in rad/s, and A denotes the magnitude of pointA's acceleration in m/s2) 1) wAB=0; wBC=0; aA=02) wAB=6,99; wBC=-7.09; aA=03) wAB=8.63; wBC=0; aA=04) wAB=8.63; wBC=0; aA >0 5) wAB=6.99; wBC=-7.09, aA>0
Rod OA rotates counterclockwise with a constant angular velocity of 0 = 5 rad/s. The double collar B is pin-connected together such that one collar slides over the rotating rod and the other slides over the horizontal curved rod, of which the shape is described by the equation = 1.5(2-cos) ft. (Figure 1) Figure r = 1.5 (2 cos 6) ft 6 = 5 rad/s 1 of 1 Part A If both collars weigh 0.60 lb, determine the magnitude of the normal force which the curved rod exerts on one collar at the instant = 140 °. Neglect friction. Express your answer to three significant figures and include the appropriate units. N = Submit μA Value Request Answer Units < Return to Assignment Provide Feedback ?
WA TB RA
Determine the velocity of rod R for 0 = T/2 rad in the cam Cif the cam rotates with a constant angular velocity w = 10 rad/s. The pin connection at o does not cause an interference with the motion of A on C. Enter the velocity of R in m/s in the box below. Assume positive to the left, as shown in the figure. ri =1 m, r2 = 0.15 m. Enter the answer in m/s in the box below. C
Determine the velocity of rod R for 0 T/2 rad in the cam C if the cam rotates with a constant angular velocity w = 10 rad/s . The pin connection at O does not cause an interference with the motion of A on C. Enter the velocity of R in m/s in the box below. Assume positive to the left, as shown in the figure. ri = 1 m, r2 = 0.15 m. Enter the answer in m/s in the box below. C www R
The rope that is wound around a drum wheel lifts the bucket, as shown in the figure. If the angular displacement of the wheel is given by the expression 0 = (0.7t³ + 1t) rad, where t is in seconds, determine the velocity of the bucket (in ft/s) when t 4.4 s. = 0.75 ft
The length of link OB is 325 mm and it is rotating about fixed axis O at a speed of 116 rev/min. Find the liner velocity of point B in m/sec. VB = m/s %3D