S Two sinusoidal voltages of maximum values 120 V and 80 V, respectively but differing in phase by 40 degrees are induced in the same branch of a circuit. What is the maximum value of the resultant voltage? Select the correct response: 266.5 V 133.2 V 144.2 V 188.4 V Continue> < Previous 28°C assignment/start/33008469#

S Two sinusoidal voltages of maximum values 120 V and 80 V, respectively but differing in phase by 40 degrees are induced in the same branch of a circuit. What is the maximum value of the resultant voltage? Select the correct response: 266.5 V 133.2 V 144.2 V 188.4 V Continue> < Previous 28°C assignment/start/33008469#

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

alculate the voltage Vs and the current Is. Calculate the phase difference between Vr1 and Vs.
Take a look at the attached screenshot. Then, write down in words you guess as to what would happen to the circuit if the below were to be adjusted. a) Frequencyb) Amplitudec) DC Offsetd) Time per Division
Which of the following statements is/are true? (A In purely inductive circuit, the current leads voltage. (B) In purely resistive circuit, the current lags voltage. C In purely resistive circuit, the current is in phase with voltage. D In purely capacitive circuit, the voltage lags current.
1. if V1 is made the reference phasor, then the resulting voltage phasor across R1 expressed as polar, will have a magnitude of _____ volts and an angle of _____ degrees. Select the correct answer below: a. 6, -53 b. 6, 53 c. -6, -53 d. -6, 53 2. if V1 is made the reference phasor, then the resulting voltage phasor across C1 expressed as polar, will have a magnitude of _____ volts and an angle of _____ degrees. Select the correct answer below: a. 8, -37 b. 8, 37 c. -8, -37 d. -8, 37 3.Regardless which phasor is made reference (V1, VR1, or VC1), the phasor diagram of R1 and C1 does not change. Select the correct answer below: a. True b. False
Draw the phasor diagram. Find magnitudes and positions of all the quantities. Please show complete solution and round off answers up to the 3rd decimal place. Thank you!
Which of the following statements is/are true? A In purely resistive circuit, the current lags voltage. (B In purely capacitive circuit, the voltage lags current. In purely resistive circuit, the current is in phase with voltage. D In purely inductive circuit, the current leads voltage.
Ro. 8. For unit- slep responses A,4 find the homafor the system. chowa ahe figure , 20 see tlJae) fimetion of
Given a series circuit comprised of the following element: 68.13-ohm resistor, practical inductor with internal resistance of 0.34 ohm and reactance of 47.15 ohms; and a capacitor with reactance of 7.53 ohms. Compute for the magnitude of its equivalent impedance in ohms. Do not round off during computation. final ans 4 decimal places
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Instruction: Provide the correct answer. 1. What is the relationship between the supply voltage and circuit current in purely capacitive circuits? 2. Vm = 100cos(377t + 75°) transform into sine form is a complex number that represents the amplitude and phase of a sinusoid. 3. 4. What is the phase relationship between a supply voltage and current through a purely inductive circuit? . 5. The rms value of the signal is also called the
1. Instruction: Provide the correct answer. 1. What is the relationship between the supply voltage and circuit current in purely capacitive circuits?. 2. Vm = 100cos(377t + 75°) transform into sine form is a complex number that represents the amplitude and phase of a sinusoid. 3. 4. What is the phase relationship between a supply voltage and current through a purely inductive circuit?. 5. The rms value of the signal is also called the 6. The It is also the cosine of the angle of the load impedance. 7. When Q < 0, the power factor is 8. The process of increasing the power factor without altering the voltage or current to the original load is known as 9. is the cosine of the phase difference between voltage and current. is the measurement to measure average power. 10. What is the meaning of VAR?
From the concepts that you have learned, fill the graphic organizer to complete the concepts of HARMONICS.