Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P-50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E-200 GPa La4m E=70 GPa L-3m A=300 mm a-11.7x10*/C A-900 mm a-23x10* /C 3 m 3 m 3 m Situation 3

Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P-50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E-200 GPa La4m E=70 GPa L-3m A=300 mm a-11.7x10/C A-900 mm a-23x10 /C 3 m 3 m 3 m Situation 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. The rigid bar weighs 5 kN/m, is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises 20°C after a load W = 150 kN is applied. A (mm?) a (FC) E (GPa) Steel rod 300 11.7 x 10-6 200 Bronze rod 1400 18.9 x 10-6 83 Bronze | 3 m Steel 1.5 m ►| 1.0 m 2.5 m 2 m W
Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
DEFORMATION DUE TO AXIAL FORCES PROBLEM 1: CE Brd Exam The rigid block shown weighs 176.4 kN. It is held in position shown with stress in the supporting rods shown initially zero. If the former is to remain horizontal when released, 1a. Find the ratio of forces in bronze and steel a. 0.389 c. 0.397 1b. Find the stress in the bronze rod. b. 0.344 d. 0.416 а. 31.92 MPа с. 28.73 МPа 1c. Find the the elongation of steel rod. b. 53.34 MPa d. 39.67 MPa a. 0.615 mm b. 1.83 mm c. 2.31 mm d. 2.12 mm 0.6 m BRONZE A=900mm STEEL STEEL A=600mm A=600mm 1 m E-200GPA E-83GPA E=200GPA W = 176.4 kN
2.47 The negligible weight rigid bar is pinned at O and attached to two vertical rods. WI is the largest load P that can be applied without exceeding stresses of 150 MPa in t steel rod and 70 MPa in the bronze rod, assuming the rods were initially stress-free? 4m 3m 3m Steel A = 600mm2 E = 83Gpa L = 4m Steel V P A = 1800mm2 E = 200Gpa L 3m
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. STEEL Lm A-400 mm E-200 GPa BRONZE L-5m A-500 mm E-80 GPa 3m
Determine the maximum force P that can be applied to the specimen. The bar is made from steel and has an allowable stress of 150 MPa. 2R = 5mm R = 20mm- PP 150mm -6mm
The light rigid bar ABCD shown below is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load P = 20 kN is applied. steel L=1.5 m A=300 mm2 2 m- E= 200 GPa B D Aluminun L=2 m P = 20 kN - 1m A= 500 mm2 E= 70 GPa
Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load P-75 KN is applied. Neglect the deformation and mass of the horizontal bar AB. Use Ea = 75 GPa, as=23.0 um/m °C. Aa 850 mm2 Es 210 GPa, as = 11.9 um/m.°C and As 650 mm2. %3D Steel Aluminum 2.5m 3m 3m 3 m 3m 75 kN
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
A 260 mm bar AB with a rectangular cross section of 17 x 30 mm, consists of two aluminium layers with cach being 6 mm thick and brazed to a centre steel layer of 5 mm thickness as shown in Figure Q3. An axial tensile force of P- 37 kN is applied to the assembly by means of a rigid end cap at B. Given that the assembly is fixed at end A and the Young's modulus of aluminium and steel are E.= 70 GPa, Es= 200 GPa, respectively, determine: i Whether this structural configuration is statically determinate or statically indeterminate, and clearly explain your reasoning. ii. The normal forces in the aluminium layers and the steel layer i. The normal stress in the aluminium layers and the steel layer. State whether the stresses are in tension or compression iv. Determine the deformation of the assembly Cross section of the bar 6 mm 5 mm 6 mm 30 mm 260 mun Aluminium. Steel- Aluminitum Nא 37 30 mm
Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load P=75 KN is applied. Neglect the deformation and mass of the horizontal bar AB. Use Ea = 75 GPa, as=23.0 µm/m-°C, Aa = 850 mm2 Es = 210 GPa, as = 11.9 µm/m-°C and As = 650 mm2 . %3D Steel Aluminum 2.5m 3m B 3 m 3 m 3 m 75 KN