[Standardization] A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCI, evaporated to incipient dryness, and quantitatively transferred to a 250 mL volumetric flask and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. [Analysis] A 30 mL unknown water sample was treated with 37.6 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. What is the concentration of Ca2+ (40.0780 g/mol) in ppm? 255.19 ppm 253.64 ppm 250.95 ppm 257.93 ppm B D

[Standardization] A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCI, evaporated to incipient dryness, and quantitatively transferred to a 250 mL volumetric flask and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. [Analysis] A 30 mL unknown water sample was treated with 37.6 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. What is the concentration of Ca2+ (40.0780 g/mol) in ppm? 255.19 ppm 253.64 ppm 250.95 ppm 257.93 ppm B D

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter4: Stoichiometry: Quantitative Information About Chemical Reactions

Section4.9: Spectrophotometry

Problem 3.1ACP

See similar textbooks

Similar questions

A 25.00 ml of Ni2+ solution was diluted in HCl and treated with 25.00 ml of 0.05283 MNa2EDTA. The solution was neutralized with NaOH followed by addition of acetate buffer untilthe pH 5.5. The solution turns yellow after addition of few drops of xylenol orange indicator.Back titration using standard 0.022 MZn2+ at pH 5.5 requires 17.61 ml until end point, onwhich the solution will turn red. Calculate for the molarity of the unknown.
A 0.5131-g sample containing KBr is dissolved in 50 mL of distilled water. Titrating with 0.04614 M AgNO3 requires 25.13 mL to reach the Mohr end point. A blank titration requires 0.65 mL to reach the same end point. Report the %w/w KBr in the sample.
[Standardization] A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCl, evaporated to incipient dryness, and quantitatively transferred to a 250 mL volumetric flask and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. [Analysis] A 30 mL unknown water sample was treated with 37.6 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. What is the concentration of CaCO3 of the unknown water sample in ppm? (MW CaCO3 = 100.0869 g/mol)? 633.43 ppm CaCO3 626.71 ppm CaCO3 637.27 ppm CaCO3 644.11 ppm CaCO3
[Standardization] A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCl, evaporated to incipient dryness, and quantitatively transferred to a 250 mL volumetric flask and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. [Analysis] A 30 mL unknown water sample was treated with 37.6 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. What is the concentration of CaCO3 of the unknown water sample in ppm? (MW CaCO3 = 100.0869 g/mol)?
The Merck Index indicates that 10 mg of guanidine,CH5N3, may be administered for each kilogram of bodymass in the treatment of myasthenia gravis. The nitrogenin a 4-tablet sample that had a total mass of 7.50 g wasconverted to ammonia by a Kjeldahl digestion, followedby distillation into 100.0 mL of 0.1750 M HCl. Theanalysis was completed by titrating the excess acid with11.37 mL of 0.1080 M NaOH. How many of thesetablets represent a proper dose for a patient who weighs(a) 100 lb, (b) 150 lb, and (c) 275 lb?
[Standardization] A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCl, evaporated to incipient dryness and quantitatively transferred to a 250 mL volumetric flask, and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was performed and was determined to be 0.4 mL. What is the concentration of EDTA obtained (MW CaCO3 = 100.0869 g/mol)? 5.050 x 10-3 M 0.1284 M 0.1262 M 5.135 x 10-3 M
[Standardization] A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCI, evaporated to incipient dryness, and quantitatively transferred to a 250 mL volumetric flask and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. [Analysis] A 30 mL unknown water sample was treated with 37.6 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. What is the concentration of CaCO3 of the unknown water sample in ppm? (MW CaCO3 = 100.0869 g/mol)? A 626.71 ppm CaCO3 B 644.11 ppm CaCO3 633.43 ppm CaCO3 637.27 ppm CaCO3 D
[Standardization] A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCI, evaporated to incipient dryness, and quantitatively transferred to a 250 mL volumetric flask and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. [Analysis] A 30 mL unknown water sample was treated with 37.6 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. What is the concentration of CaCO3 of the unknown water sample in ppm? (MW CaCO3 = 100.0869 g/mol)? A 644.11 ppm CaCO3 637.27 ppm CaCO3 C 633.43 ppm CaCO3 626.71 ppm CaCO3
[Standardization] A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCI, evaporated to incipient dryness and quantitatively transferred to a 250 mL volumetric flask, and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was performed and was determined to be 0.4 mL. What is the concentration of EDTA obtained (MW CaCO3 = 100.0869 g/mol)? A 0.1284 M B 0.1262 M C) 5.135 x 10-³ M D 5.050 x 10-³ M
[Standardization] A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCI, evaporated to incipient dryness and quantitatively transferred to a 250 mL volumetric flask, and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was performed and was determined to be 0.4 mL. What is the concentration of EDTA obtained (MW CaCO3 = 100.0869 g/mol)? A) 0.1262 M B) 0.1284 M D 5.135 x 10-³ M 5.050 x 10.³ M
A solid containing tris was dissolved in water and brought to a total volume of 50.00 ml. A 10.00 ml aliquot of the solution was titrated with 0.09978 M HCl to a bromcresol green endpoint. The aliquot consumed 38.93 ml of titrant. Calculate the weight of tris in the original sample.
A 0.5264-g sample containing KBr is dissolved in 50 mL distilled water. Titrating with 0.04738 M AgNO3 requires 24.57 mL to reach the Mohr endpoint. A blank titration requires 0.75 mL to reach the same endpoint. Report the % (w/w) KBr (MM = 119.0) in the sample. 26.19% 51.02 % 12.76 % 25.51 %