For the retaining wall shown above calculate the following: A) Calculate the value of K (for either the 'active' or 'passive' earth pressure - whichever is appropriate! ...you decide). B) Calculate and sketch the pressure distribution on the 'back' side (soil side) of the retaining wall (show all of the relevant pressure distributions and indicate the magnitude of the distributions on the sketch). Indicate the correct units! C) Calculate the resultant horizontal force for each pressure distribution and calculate the total overturning moment about the base of the wall. Show the forces in the correct units!

For the retaining wall shown above calculate the following: A) Calculate the value of K (for either the 'active' or 'passive' earth pressure - whichever is appropriate! ...you decide). B) Calculate and sketch the pressure distribution on the 'back' side (soil side) of the retaining wall (show all of the relevant pressure distributions and indicate the magnitude of the distributions on the sketch). Indicate the correct units! C) Calculate the resultant horizontal force for each pressure distribution and calculate the total overturning moment about the base of the wall. Show the forces in the correct units!

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter13: Retaining Walls

Section: Chapter Questions

Problem 13.6P

See similar textbooks

Similar questions

A 60 cm Cl main pipe leads from a reservoir whose water surface is at Elev. 1590 m. Below the ground surface level, the main pipe is horizontally positioned at Elev. 1410 m. Assuming static condition, what is the stress in the pipewall if the wall thickness is 12.50 mm and the soil pressure is 520 kPa? a. 18.2 MPa O b. 20.5 MPa O . 28.7 MPa O d. 32.6 MPa
A 60 cm CI main pipe leads from a reservoir whose water surface is at Elev. 1590 m. Below the ground surface level, the main pipe is horizontally positioned at Elev. 1410 m. Assuming static condition, what is the stress in the pipewall if the wall thickness is 12.50 mm and the soil pressure is 520 kPa? a.18.2 MPa b.32.6 MPa c.20.5 MPa d.28.7 MPa
6. Determine ax and ay in the figure for problem 5 if the pressure at A, B and C is the same. Ans. ax = 0, ay = -g
H 10m 6m SATURATED CLAY Yo=19 kN/m 2.5m SAND A175 kN/m Calculate the max. depth of cut H, that a) can be made in the clay. Calculate the effective stress of A. b) c) Calculate the effective stress at B. Scanned with CamScanner
Consider the figure shown: (65.73, 19.45, 1.13, 1.37) 0.70m 0.28 Im 2im Soil çe0.52) Ga'- 2.72 0 valve open In flow Compute the pore pressure at B. b. Compute the effective stress at C. c. Compute the critical hydraulic gradient. d. Compute the seepage force per unit volume
sla ra CJI Y:- اليوم تحربر Refer to the soil profile shown in figure below CALCULATE PORE WATER PRESSURE (uc ) AT POINT C G.W.T Sand 5m Y sat = 20.9 B. Clay Ysat = 17. 8 4m Let the point A at depth "0". point B at depth "Sm", and point C at depth 9m Select one: a. 87.29 KN/m2 b. 48.29 KN/m2 O c. 81.29 KN/m2 d. 88.29 KN/m2
Consider the retaiming wall shown in the Figure below Calculate the Rankine passive force per unit length of the wall and the location of the line of action of that resultant at which it acts on the retaming wall, - 15.72KN/m3 1=30 C1=0 2. WT rsat3D15.72KN/m3 12=26 E C1-10KN/m2 For the frictionless wall retaining a stratified soil and shown in Fig. E3.2, determine: (a) The active lateral earth pressure distribution with depth. (b) The passive lateral earth pressure distribution with depth. (c) The magnitude and location of the active and passive forces. (d) The resultant force. (e) The ratio of passive moment to active moment. 4, - 20 kPa m 7s19 kNms d =250 C-O Yser=20 kNm ダ=30 Hm
For a cutoff wall shown in Figure 4a. Establish the flow nets (i.e. flow and equipotential lines) following all the rules (Drawdirectly on Figure 4).b. Deten:nine the quantity of seepage (m3/s perm) (coefficient of permeability, k = 2.0 x10·5 mis).c. Calculate the effective stress at point A (back of the piling) (Yu.t = 20 kNlm\d. Estimate the stability of the cutoff wall using lhe Factor of Safety, FS.
320 Chapter 5 Distributed Forces 5/177 Calculate the depth h of mud for which the 3-m concrete retaining wall is on the verge of tipping about its forward edge A. The density of mud may be taken to be 1760 kg/m and that of concrete to be 2400 kg/m. Ans. h = 1.99 m %3D 0.8 m 3 m Mud Problem 5/177 5/178 The two hemispherical shells are perfectly sealed
Homework
PROBLEM 1. In a hydraulically smooth pipe flow, wall shear stress (to) is measured as 1.5 N/m2. Pipe diameter is 0.2 m. a) Please draw velocity profile in the pipe (for the half of the pipe) by using a 0.0001m interval of the distance from the pipe wall (y) (i.e. y = 0, 0.0001, 0.0002, ...). You need to use Microsoft Excel for doing this calculation considering the high number of calculation points. (The fluid is water with a kinematic viscosity (v) of 10-6m/s and density of 1000 kg/m2.) (You may draw two separate graphs for viscous sublayer and core region.) Table 1. Example calculation table y (m) u (m/s) 0.0001 0.0002 0.0003 0.0999 0.1 b) Calculate cross sectional average flow velocity for this flow by using your calculated values. c) Calculate cross sectional average flow velocity for this flow by using the related equations given in the lecture notes. Compare this calculation with your previous value in b. You need to submit a short report of maximum one page showing your…
For the retaining wall below: (a).Determine the lateral earth pressure distribution due only to the distributed load. Show your work (e.g., sample calculation) to plot the graph for distribution. b.Determine and plot the total lateral earth pressure distribution acting on the wall (assuming drained, active conditions).