Suppose a long bone is idealized as a solid cylinder with a diameter of 0.03 m. During a torsion test, if the torsion moment is 10N.m, what is the maximal stress caused by torsion? (Hint: polar moment of inertia of the cross-sectional area is equal to π r4/2 , π = 3.14, r is the radius).

Suppose a long bone is idealized as a solid cylinder with a diameter of 0.03 m. During a torsion test, if the torsion moment is 10N.m, what is the maximal stress caused by torsion? (Hint: polar moment of inertia of the cross-sectional area is equal to π r4/2 , π = 3.14, r is the radius).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.8P: - A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s...

See similar textbooks

Similar questions

A stress-strain diagram for a tension test of an alloy steel sample is shown in the diagram below. The initial sample diameter is 0.502”, the diameter of the fractured sample is 0.412”, the original gage length is 2.00” and the final length after fracture is 2.78”. Determine/ calculate the following: (a) The stress at the proportional limit. (b) The modulus of elasticity (E). (c) The yield stress using the 0.2% offset method. (d) Theultimatetensilestrength. (e) The rupture stress. (f) The percent reduction in area. (g) The percent elongation. (h) Is the material considered ductile or brittle?
The data shown in the accompanying table are From a tensile test of high-strength steel. The test specimen has a diameter of 0.505 in. and a gage length of 2.00 in. (see figure for Prob. 1.5-3). At fracture, the elongation between the gage marks is 0.12 in. and the minimum diameter is 0.42 in. Plot the conventional stress-strain curve for the steel and determine the proportional limit, modulus of elasticity (the slope of the initial part of thestress-strain curve), yield stress at 0.1% offset, ultimate stress, percent elongation in 2.00 in., and percent reduction in area. TENSILE-TEST DATA FOR PROB. L.5-7 Laid (lb) Elongation (in) 1000 0.0002 2000 0.0006 6000 0.0019 10,000 0.0033 12,000 0.0039 12,900 0.0041 13,400 0.0047 13,600 0.0054 13,800 0.0063 14,000 0.0090 14,400 0.0102 15,200 0.0130 16,800 0.0230 18,400 0.0336 20,000 0.0507 22,400 0.1108 22,600 Fracture
A sample test rod made of a ferrous material of 0.5 in. diameter was tested for tensile strength with the gauge length of 2.5 in. The following observations were recorded: Final length = 3.15 in; Final diameter = 0.275 in; Yield load = 7650 lb. and Ultimate load = 10375 lb. (a) Calculate: 1. yield stress, 2. ultimate tensile stress, 3. percentage reduction in area, and 4. percentage elongation. (b) What specific material, if any, is similar to this tested rod? Refer to AT7 and AT8. (c) This same material is then used as a tension member 55 inches long and is subjected to a maximum load of 6000 lb, repeated but not reversed. (d) Solve part (c) if the total elongation is not to exceed 0.025 in.? 1. %3D
A solid round bar of diameter 250mm has a tensile force of 0.2kN acting on it. What is the stress acting on the bar?
The Highest load sustained druing an uniaxial tensile testing experiment is 7,500lb. If the original cross section has a diamter of 0.25in, what is the ultimate tensile strength? (please also make a drawing)
A solid truncated cone is subject to an axial force P as shown. The exact elongation is d = PL/ (2pc²E). Replace the cone by n equal thickness circular cylinders and derive the expression as a function of n, P, L, C, E. draw a graph showing variation in elongation d with respect to n values. Take n from 1 to 100. Given that the P = 1 kip, L = 12 inch, C= 4 inch, E = 30x10° psi. B 2c
1. The greatest tensile stress that steel of a particular sort can withstand without breaking is about 10⁹ N m². A wire of a cross-sectional area 0.01 mm² is made of this steel. What is the greatest force that it can withstand? 2. Find the minimum diameter of an alloy cable, tensile strength 75 MPa, needed to support a load of 15 KN? 3. Calculate the tensile stress in a suspension bridge supporting cable, of a diameter of 50 mm, which pulls up on the roadway with a force of 4 kN.
A tensile test was conducted on a mild steel& the following data was obtained as follows. Diameter of the steel bar = 3 cm,Gauge length of the bar = 20 cm. Load at elastic limit = 250 kN . Extension at a load of 150kN = 0.21 mm . Maximum load = 380 kN . Total extension = 60 mm . Diameter of the rod at failure = 2. 25 cm Determine: (a) Young’s modulus (b) stress at elastic limit (c)the percentage of elongation (d) Percentage decrease in area.
Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a material having a Young's modulusE=120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 4.995 mm. determine the applied force F.
Sketch a tensile member with (a) a rectangular crosssection, (b) a solid circular cross section, and (c) a circulartubecross section, and label the dimensions symbolically (e.g.,label the radius for the solid circular case). For each member, write out the definition of engineering stress in terms of the actual dimensions of the component. If therectangular member has dimensions of width and thicknessequal to 1 cm 0.3 cm, what would be the radius of a solidcircular member such that the stress is equal for an equaltensile load? If a tube has an outer radius equal to that ofthis same solid cylinder, what is the maximum inner radiussuch that the stress does not exceed 200% of the stress inthe solid cylinder?
*O llAsiacell Strength of m. -> 02: A steel specimen 12mm diameter has gauge length 50mm. the steel specimen had tested via tensile test under maximum load 66KN with elongation 7.5mm, and the yield load of this specimen is 15KN with elongation 2.4mm. Calculate: 1- The engineering ultimate stress (ultimate tensile strength), and engineering strain at this point. 2- The engineering stress and strain at yield point. 3- The modulus of elasticity, and the modulus of resilience. 4- The final or fracture strain of a steel specimen, if you know that the final length of specimen after testing is 58.5mm. 5- The true stress and strain for ultimate point. Q3: The yoke-and-rod connection is subjected to a tensile force of 15 kN. Determine the average normal stress in each rod and the average shear stress in the pin A between the members. Finally, find the shear strain in pin A. Take G teef 75GPA 40 mm 15 kN, 30 mm 30 mn 15 kN 04: In figure as shown below, assume that a 35mm diameter rivet joint the…
A Brass specimen is subjected to a Tensile test in a laboratory. The following data obtained are: Length of Specimen = 367 mm; Diameter of Specimen = 19 mm; Yield Stress = 124 N/mm?: Ultimate Stress = 217 N/mm?: Fracture Stress = 183 N/mm?: % of Elongation = 50 % % of Reduction in area = 27 %. Determine the elongation at 103 kN, Load at yielding. Maximum load, Load at fracture, Final Length & Final diameter. Take Young's Modulus as 104 GPa.